HAI Omni-Bus 6-Channel Keyfob Remote Control

Model 125A00-1

®

 

User’s Guide

SPECIFICATIONS

o6 Channels

oFor use with HAI Omni-Bus Output devices

oRequires an HAI Omni-Bus RF Transceiver on an Omni-Bus network

oFrequency: 433.92MHz

oRange: Up to 30m (indoors), up to 100m (outdoors)

REMOTE CONTROL FUNCTIONS

To switch a device ON or OFF

Press and release the button on the Remote Control. The remote control will toggle between the ON and OFF commands each time the button is pressed.

To DIM a light (when used with an Omni-Bus Dimmer unit)

Enter DIM/BRIGHT mode on the Remote control by pressing buttons 1 and 2 simultaneously.

Press and hold the appropriate button on the Remote Control to dim or brighten the light.

The Remote Control will exit the DIM/BRIGHT mode automatically if no buttons are pressed for 7 seconds.

A forced exit can be achieved by pressing buttons 1 and 2 simultaneously again.

OMNIBUS PROGRAMMING

See the HAI OMNIBUS Software User Guide for more information on how to program the remote control into an Omni-Bus output devices using the OMNIBUS Installation Software.

MANUAL PROGRAMMING

1.Place the receiving device into the programming mode. This is normally done by pressing and holding the button on the receiving device until its LED starts flashing continuously. (See receiving device user guide for more information).

2.

Press and hold the DESIRED channel button on the Remote Control until the remote sounds 3 beeps (approx.10 seconds). Check for a confirmation signal from the receiving device. (See receiving device user manual for more information).

3.Exit the programming mode on the receiving device.

REMOTE CONTROL BATTERY REPLACEMENT

If the remote control does not respond to any key presses or the LED fails to come on when a key is held in, the battery may need replacement.

The remote control uses one type 23A 12V battery.

DELETING A REMOTE CONTROL

A Remote Control channel programmed into an Omni-Bus receiving device may be deleted from that device via the OMNIBUS Installation Software or by following the procedure below:

1.Place the receiving device into the programming mode. This is normally done by pressing and holding the button on the receiving device until the receiving device LED starts flashing continuously (see receiving device user guide).

2.

Press and hold the appropriate button on the remote control until the remote sounds 3 beeps followed by another set of 4 beeps. Check for a confirmation signal from the receiving device. (See receiving device user manual for more information).

3.Exit the programming mode on the receiving device.

DELETE ALL

All remote control channels programmed into ANY Omni-Bus RECEIVING device can be deleted entirely by using any Omni-Bus Remote Control. The remote control used for this does not necessarily need to be one that was previously programmed into the device. This allows a lost or stolen remote control to be deleted before reprogramming the new remote control.

1.Place the receiving device into the programming mode. This is normally done by pressing and holding the button on the receiving device until the receiving device LED starts flashing continuously (see receiving device user guide).

2.

Press and hold any button on the remote control until the remote sounds 3 beeps, then 4 beeps and then 5 beeps (approximately 17 seconds). Check for a confirmation signal from the receiving device. (See receiving device user manual for more information).

3.Exit the programming mode on the receiving device.

KEYPAD LOCK FUNCTION

The keypad lock function can be used to prevent accidental remote control activation.

Enabling the Keypad Lock Function

Before the keypad lock function can be used, it has to be enabled as follows: Press and hold button 3 and 4 simultaneously until the remote sounds a burst of beeps (after approximately 5 seconds).

Disabling the Keypad Lock Function

Press and hold button 3 and 4 simultaneously until the remote sounds a short beep (after approximately 5 seconds).

Locking/Unlocking the Keypad

Lock or Unlock the Keypad on the Remote Control by pressing buttons 3 and 4 simultaneously. The Remote Control will sound a long beep when the Keypad is locked and any key is pressed on the remote control.

© 2010 Home Automation, Inc.

www.homeauto.com

Document: 125I00-1, Rev1.0 May 2010

Page 1 Page 1
Page 1
Image 1
Home Automation 125A00-1 specifications Specifications, Remote Control Functions, Omnibus Programming, Manual Programming
Page 1 Page 1

125A00-1 specifications

Home automation has rapidly advanced, providing users with unprecedented control over their living spaces. One notable product in this field is the Home Automation 125A00-1, designed to enhance convenience, security, and energy efficiency.

The Home Automation 125A00-1 is equipped with a cutting-edge smart hub that acts as the central control system for various connected devices throughout the home. This hub is compatible with numerous technologies, including Wi-Fi, Zigbee, and Z-Wave. This multi-protocol support ensures that users can connect a variety of smart devices, from lighting and thermostats to security cameras and locks, regardless of the brand.

One of the standout features of the 125A00-1 is its user-friendly mobile app, which allows homeowners to monitor and control their devices remotely. This app provides real-time notifications, scheduling options, and the ability to create customized scenes that enhance daily routines. For instance, users can create a "Movie Night" scene that dims the lights and sets the thermostat to a cozy temperature with a single command.

In terms of security, the Home Automation 125A00-1 integrates seamlessly with smart security systems. Users can receive alerts about unusual activity, remotely lock doors, and view live feeds from their security cameras. Additionally, the system supports geofencing technology, enabling the automated locking and unlocking of doors as users approach or leave their homes.

Energy efficiency is another critical aspect of the 125A00-1. The system can monitor energy usage of connected devices and provide insights into consumption patterns. This information empowers homeowners to make more informed decisions about energy usage, potentially leading to lower utility bills. Smart thermostats can learn preferences over time and adjust heating and cooling schedules automatically for optimal efficiency.

Moreover, the Home Automation 125A00-1 prioritizes user privacy and security. With end-to-end encryption for data transmission and frequent software updates, users can trust that their information remains secure.

In summary, the Home Automation 125A00-1 represents a significant leap in smart home technology, offering a versatile, user-friendly, and secure solution for modern living. With its extensive features and compatibility with various devices, it stands out as an excellent choice for anyone looking to embrace the convenience of home automation.
Top Page Image Contents