Honeywell installation instructions DT7450UK2 Dual TEC Motion Sensor Product Information

DT7450UK2 DUAL TEC® Motion Sensor Product Information

LED INDICATORS

LED		OPERATION MODE
	Normal	Power Up	Fault	Zone Finder
Red	ON	Slow	Fast	OFF
	Alarm	Blink	Blink
Yellow	ON	OFF	OFF	ON
	Microwave			Microwave
Green	ON	OFF	OFF	ON
	PIR			PIR

DIP SWITCH SETTINGS (SW1)

Factory default settings are shown in grey.

Switch	OFF	ON
1	Low Sensitivity	High Sensitivity
	(Pulse Count 2)	(Pulse Count 1)
2	LED disabled	LED enabled

TROUBLESHOOTING

Problem: Red LED is flashing rapidly.

Explanation: The sensor is in one of three conditions:

Microwave supervision failure: The sensor continues operating using PIR as the only detection method. When detection occurs on the PIR channel, the alarm relay will latch open until the Microwave fault is removed.

PIR self-test failure: Alarm relay does not actuate.

Temperature compensation failure: When alarm occurs, the alarm relay will latch open until the fault is cleared.

Solution: Power down the sensor or enter zone finder mode which will perform self-test. If the fault does not clear, replace the sensor.

DETECTION PATTERNS

Top View

Wide Angle Lens

Minimum Detection Pattern

Side View

Maximum Detection Pattern

PRODUCT SPECIFICATIONS

Range:

15 m x 18 m

Alarm relay: Energized Form A 30 mA, 24 VDC,

40 Ohms resistance maximum

Tamper switch: (NC) 30 mA, 24 VDC

Power requirements:

7.5 - 16 VDC

25 mA typical, 30 mA maximum,

12 VDC nominal

Microwave frequencies: 24.200 GHz

PIR white light immunity: 6,500 Lux typical

Fluorescent light filter:

50 Hz

Operating temperature:

-10oC to +55o C (14o F to +131o F)

5- 95% relative humidity (non-condensing) (Indoor use environment)

Temperature Compensation:

Advanced dual slope.

Self-tests:

Microwave Supervision

PIR Self-Test

Temperature Compensation

PIR fields-of-view:

High Security Lens

22 long range edges

12 intermediate edges

6 lower edges

4 look-down edges

Weight:

174 g;

Packaged Product Approx.: 213 g

Dimensions:

11.9 cm H x 7.1 cm W x 4.2 cm D

Sensitivity:

High (Pulse Count 1) 1 - 2 steps

Low (Pulse Count 2) 3 - 4 steps

Accessories: Optional Lens Kit -

Long Range Curtain Lens Kit (P/N DT7000-LRLK) Mounting Brackets -

SMB-10 Swivel Mount Bracket (P/N 0-000-110-01)

SMB-10T Swivel Mount Bracket w/Tamper (P/N 0-000-155-01)

SMB-10C Swivel Mount Ceiling Bracket (P/N 0-000-111-01)

TS 50131-2-4 Compliant Accessories: SMB-10T Swivel Mount Bracket w/ Tamper

(P/N 0-000-155-01)

Long Range Curtain Lens Kit (P/N DT7000-LRLK)

Approvals/listings:

CE PD6662

EN 50131-1 and TS 50131-2-4 Security Grade 2, Environmental Class II.

Suitable for connection to an EN 60950 Class II Limited Power Source.

Note: In TS 50131-2-4 compliant installations: mount the sensor at 2.3 m, select the high sensitivity setting, and install a cover screw (included).

To obtain applicable EU compliance Declaration of Conformities for this product, please refer to our Website, http://www.security.honeywell.com/hsce/ international/index.html. For any additional information regarding the compliance of this product to any EU specific requirements, please contact:

Quality Assurance Department, Honeywell Security & Custom Electronics, Newhouse Industrial Estate Motherwell,

Lanarkshire ML1 5SB, Scotland,

United Kingdom.

Tel: +44(0)1698 738200

Email: UK64Sales@Honeywell.com.

© 2008 Honeywell International Inc. • Honeywell, IntelliSense and DUAL TEC are registered trademarks of Honeywell International Inc.		Please contact your local authorised Honeywell
All other trademarks are the properties of their respective owners. All rights reserved.	Made in China
		representative for product warranty information.

800-02414 Rev B