3 Inch Dome Camera HD3VC4SHR/HD3VC4SA/HD3VC4SHRX/HD3VC4SAX
Quick Install Guide
Operating Conditions
• | Avoid viewing very bright objects (example, | |
| light fixtures) for extended periods. | |
• | Avoid operating or storing the unit in the | |
| following locations: | |
| • | Extremely humid, dusty, hot/cold |
|
| environments (where the operating |
|
| temperature is outside the |
|
| recommended range of 14°F to 122°F |
|
| |
| • | Close to sources of powerful |
Removing the Dome Cover
1.Gently turn the dome cover (#5 on Figure 2)
2.Remove the inner liner (#4) by gently pulling it free of the two notches (#2) in the housing (#1).
3.Set the dome (and liner) aside.
Figure 2 Dome Cover Removal
Figure 4 Camera Adjustment
5
1
2
3
4
4 — Legend
| electromagnetic radiation, such as |
| radio or TV transmitters |
• | Close to fluorescent lamps or objects |
1
1
2
Tilt adjustment bracket and thumbnuts (x2) for vertical adjustment
Axis ring for horizontal rotation for wall mount and tilted ceilings
| reflecting light |
• | Under unstable light sources (may |
| cause flickering) |
2
3
3Zoom lever
4Focus lever
4
5
Rotate 3D assembly in base for horizontal adjustment
Document 900.0824 - 09/06 - Rev 1.01
Introduction
The unobtrusive, compact design of the HD3VC4S Series 3 Inch Dome Camera is ideal
2 — Legend
1 Camera housing
2 Notches (x2)
Adjusting the Lens
1. Loosen the Zoom lever (#3) counter- |
clockwise a little, then rotate the Zoom |
for indoor installations in commercial and
3
Tilt adjustment bracket and thumbnuts
lever and determine the image view. |
Warnings, Operating Notes
residential environments.
5
4 Inner liner
5 Dome cover
2. Loosen the Focus lever (#4) counter- |
clockwise a little, then adjust the focus for |
optimum picture sharpness. |
Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty.
WARNING! The use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards.
WARNING! To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the European Union and other European countries with separate collection systems). This product should be disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.
|
|
|
|
|
|
| CAUTION |
|
|
| THIS SYMBOL INDICATES |
| RISK OF |
|
|
| THAT DANGEROUS VOLTAGE |
|
|
|
| CONSTITUTING A RISK OF | |
| ELECTRIC SHOCK |
|
|
| ELECTRIC SHOCK IS |
|
|
|
|
| |
|
|
|
|
| PRESENT WITHIN THE UNIT. |
|
|
|
| ||
CAUTION: TO REDUCE THE RISK OF ELECTRIC |
| THIS SYMBOL INDICATES THAT | |||
SHOCK, DO NOT REMOVE THE COVER. |
| IMPORTANT OPERATING AND | |||
NO |
| MAINTENANCE INSTRUCTIONS | |||
REFER SERVICING TO QUALIFIED |
| ACCOMPANY THIS UNIT. | |||
| SERVICE PERSONNEL |
|
| ||
|
|
|
|
|
|
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Caution Changes or modifications not
Before You Begin
Please read this guide carefully before you install the HD3VC4S Series 3 Inch Dome Camera. Keep this guide for future reference.
Unpack Everything
Check that the items received match those listed on the order form and packing slip. The HD3VC4S Series Camera packing box should include, in addition to this Install Guide:
•One fully assembled camera
•One hardware kit
•One 2nd video monitor output cable
•One mounting template
If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service.
Installation
The HD3VC4S Series is a
Figure 1 Camera Parts
b
a
1
2
3
4
5
1 — Legend
Connecting the Wiring
Follow Figure 1 to connect the video output connector (a) and 24 VAC/12 VDC power connector (b).
Caution For DC power supply use, make sure the polarity is correct to avoid malfunction and/or camera damage.
Mounting the Camera
1.Place the mounting template (supplied) on the mounting surface and mark the holes (see Figure 3).
2.Drill two holes, then insert the screw anchors into the holes.
3.Secure the camera housing to the wall/ ceiling with the TP4 x 15 mm tapping screws supplied.
Note Depending on the material of your mounting surface, you may require different screws and anchors than those supplied.
Figure 3 Camera Installation
1
2
M o u n t in g T e m p la t e
L o g o D i r e c t i o n
3
MON
PC |
|
S |
|
E |
|
A |
|
CC/ |
|
LGCL |
|
BADL |
|
:::: |
|
1234 |
|
4 | T |
3 | PO |
2 |
|
1 |
|
N FF |
|
O O |
|
L |
|
EVEL | - |
L H | S E |
| A |
| P H |
| V+ |
3. |
after adjustment. |
Note It is important that you lock the zoom and focus levers after making adjustments. This will avoid the positions moving (for example, from temperature changes or vibrations).
Optional Camera Settings
See Figure 5 for location on the camera board of the camera adjustment functions described below.
Figure 5 Camera Adjustment Functions
| 1 |
|
|
|
|
| 3 |
| 1 : B LC |
| LEVEL |
|
|
|
| 1 2 3 | 4 | ||
|
|
|
|
|
| 2 : AG C | |||
|
| H | L |
|
|
| O N |
| |
|
|
|
|
|
| 3 : D C /A ES | |||
|
|
|
|
|
|
| O FF |
| |
|
|
|
|
|
|
|
| 4 : LL | |
|
|
|
|
|
|
|
|
| |
2 |
|
|
|
|
|
| 4 |
|
|
V PH A SE |
|
|
|
|
|
| M O N | ||
+ | - |
| 1 | 2 | 3 | 4 |
|
|
|
|
|
| 1:BLC |
|
| ||||
|
|
| O N |
|
|
| 2: AG C |
|
|
|
|
| O FF |
|
|
| 3:DC/A E S |
|
|
|
|
| L E V E L |
|
|
| 4:LL |
|
|
|
|
| H L |
|
|
| P |
|
|
|
|
|
|
|
|
| C |
|
|
|
|
| V P HA S E |
| P OT |
|
|
| |
|
|
| + - |
|
|
| M |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| O |
|
|
|
|
|
|
|
|
| N |
|
|
5
5 — Legend
1LEVEL adjustment pot (Iris level)
2V Phase adjustment pot (24 VAC only)
3Mode setting DIP switches
4Monitor out
5Camera mounting holes
Note Please use the supplied DC Iris and Line lock adjustment tool to adjust picture brightness and phase adjustment.
Picture Brightness Use the LEVEL screw (#1) to compensate for the iris level. L (low) makes the picture darker. H (high) makes the picture brighter.
expressly approved by the party responsible for compliance could void
1
Conduit hole used for surface run power/video connector
3 — Legend
1 Screw anchors (x2), supplied |
Phase Adjustment Use the V Phase
the user’s authority to operate the equipment.
2Camera housing
3Dome cover
2 | Mounting template |
|
|
3 | TP4 x 15 mm tapping screws (x2) supplied |
Adjustment Pot (#2) to adjust the phase difference between cameras. Make sure Switch
This Class A digital apparatus complies with Canadian
Manufacturer’s Declaration of
4Zoom lever
5Focus lever
aVideo output connector
Adjusting the Camera Position
The HD3VC4S Series camera has three axes for
4 is ON to activate the Line lock function (AC operation only).
DIP Switches Set the DIP switches (#3) to activate or deactivate the following functions:
Conformance
b
24 VAC/12 VDC power input connector (red +, black
positioning the camera. While monitoring the picture on the monitor, adjust the camera
The manufacturer declares that the equipment supplied with this guide is compliant with the essential protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN 55022 for emissions.
Operating Notes
Power Supply
This dome camera can operate on 24 VAC or 12 VDC.
Note See Figure 5 for an explanation of the camera board settings.
position as follows:
Horizontal Adjustment Rotate the 3D assembly in the base. Do not turn the assembly more than 360° as this may cause the internal cables to twist and disconnect or break.
Vertical Adjustment After loosening the thumbnuts, position the camera as desired, then
Horizontal Rotation For Wall Mount and Tilted
Ceilings Rotate the lens base (maximum 360°) until you are satisfied with the field of view.
Switch Description
1BLC (Backlight Compensation). Set to ON to have the camera adjust the exposure to compensate for situations where the subject is lit from behind. The factory default setting is OFF.
2AGC (Automatic Gain Control). Set to ON (default) to have the camera adjust the picture for low light conditions.
3DC/AES Mode. Leave in ON position only.
4LL (Line Lock). Set the camera synchronization to internal or line lock (line lock is only available with 24 VAC). The factory default setting is OFF.
Document 900.0824 - 09/06 - Rev 1.01