Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance (see Assistance).

EN

Problem:

Possible causes / Solutions:

 

 

The dishwasher does not start or

• Switch off the appliance by pressing the ON/OFF button, switch it back on after

cannot be controlled

approximately one minute and reset the program.

 

• The appliance has not been plugged in properly.

 

• The dishwasher door has not been shut properly.

 

 

The door won’t close

• The lock was released. Strongly push the door until a “clacking” noise is heard.

 

 

No water drains out from the

• The dishwasher cycle has not yet finished.

dishwasher.

• The water inlet hose is bent (see Installation).

 

• The drain duct is blocked.

 

• The filter is clogged up with food residues.

 

 

The dishwasher makes excessive

• The dishes are rattling against each other or against the sprayer arms.

noise.

• An excessive amount of foam has been produced: the detergent has not been

 

measured out correctly or it is not suitable for use in dishwashers (see Start-up and

 

use).

 

 

The dishes and glasses are

• The level of the refined salt is low or the dosage setting is not suited to the hardness

covered in a white film or

of the water (see Rinse aid and salt).

limescale deposits.

• The lid on the salt dispenser is not closed properly.

 

• The rinse aid has been used up or the dosage is too low.

 

 

The dishes and glasses are

• The rinse aid dosage is too high.

streaked or have a bluish tinge.

 

 

 

The crockery has not been dried

• A wash cycle without a drying program has been selected.

properly.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).

 

• The rinse aid dispenser setting is not suitable.

 

• The crockery is made from non-stick material or plastic.

 

 

The dishes are not clean.

• The racks are overloaded (see Loading the racks).

 

• The crockery has not been arranged well.

 

• The sprayer arms cannot move freely.

 

• The wash cycle is too gentle (see Wash cycles).

 

• An excessive amount of foam has been produced: the detergent has not been

 

measured out correctly or it is not suitable for use in dishwashers (see Start-up and

 

use).

 

• The lid on the rinse aid compartment has not been shut correctly.

 

• The filter is dirty or blocked (see Care and maintenance).

 

• The refined salt level is low (see Rinse aid and salt).

 

 

The dishwasher does not take any

• There is no water in the mains supply.

water in - Tap shut-off alarm

• The water inlet hose is bent (see Installation).

(The ON/OFF indicator light flashes and

• Turn on the tap and the appliance will start after a few minutes.

the display shows A-6).

• The appliance lock has been activated because no action was taken when the

 

beeps sounded.

 

Switch off the appliance using the ON/OFF button, turn on the tap and switch the

 

appliance back on after 20 seconds by pressing the same button. Re-program the

 

appliance and restart the wash cycle.

 

 

Water inlet hose alarm / Water inlet

• Switch off the appliance by pressing the ON/OFF button. Shut off the water tap to

filter blocked

eliminate the risk of flooding and remove the plug from the electrical socket.

(the ON/OFF indicator light flashes and

Make sure the water inlet filter has not become blocked by impurities (see “Care

the display shows A-7).

and maintenance” chapter).

 

 

*Only available in selected models.

14

Page 14
Image 14
Hotpoint FDFF manual Troubleshooting, Problem Possible causes / Solutions

FDFF specifications

The Hotpoint FDFF is a modern appliance designed to enhance kitchen functionality while maintaining a sleek aesthetic. This fridge-freezer combination stands out due to its efficient use of space, making it an ideal choice for both small and large kitchens. With its impressive storage capacity, the FDFF has been engineered to cater to the needs of busy households.

One of the primary features of the Hotpoint FDFF is its innovative No Frost technology. This advanced system prevents the accumulation of frost by circulating chilled air, ensuring that both the fridge and freezer compartments maintain consistent temperatures. As a result, food stays fresh for longer periods, minimizing waste and enhancing food preservation.

In addition to No Frost, the FDFF features an Energy Efficiency Class of A+, which significantly reduces energy consumption compared to older models. This not only helps to lower household energy bills but also promotes eco-friendly practices, aligning with contemporary emphasis on sustainability.

Another noteworthy characteristic of the Hotpoint FDFF is its adaptable storage solutions. Inside, consumers will find adjustable shelves and a variety of compartments, including door bins and transparent drawers in the freezer section. This design offers flexibility, allowing users to organize groceries according to personal preferences and needs.

The fridge is equipped with LED lighting, which provides better visibility while using less energy. The lights are strategically placed to illuminate every nook and cranny, making it easy to find ingredients quickly, even during late-night snacking sessions.

Furthermore, the FDFF showcases a stylish design with a stainless steel finish that easily complements any kitchen décor. Its built-in handle provides a seamless look while ensuring easy access.

Among its other features, the FDFF includes a temperature alert system that notifies users if the internal temperature rises too high, safeguarding against spoilage. This high-tech alert mechanism works in conjunction with its MultiFlow technology, which enhances air circulation for even cooling throughout the fridge and freezer.

In summary, the Hotpoint FDFF is a perfect blend of innovative technology and thoughtful design. With features like No Frost technology, energy efficiency, customizable storage options, and a chic exterior, it is an excellent choice for any modern home looking to enhance its kitchen experience.