Installation
Choose where you want to install your dishwasher, you can place it so that its sides or back panel are side by side with furniture or up against the wall. The dishwasher is providedwithwatersupplyanddrain hoses, which can be directed towards the left or right to facilitate appropriateinstallation.
Levelling.
Once the appliance is positioned, adjust the feet by screwing them in or out depending on how high you want it and to level it so that it is horizontal. Make sure that it is not inclined more than 2 degrees. If the applianceislevel,itwill helpensure its correct operation.
Cold water connection. Connect the cold water supply hose, and making sure that it is fastened tightly in place . If the water hoses are new or have been outofuseforanextendedperiodof time, let the water run to make sure it is clear and free of impurities beforemakingtheconnection.Ifthis precaution is not taken, the water inlet could get blocked, causing damage to your dishwasher.
Connect to the Water Supply... | Standpipe: | SinkWasteSystem: | |
- For your dishwasher to operate | Ensure that the hose is not pushed | For under sink drainage: | |
correctlyitrequireswaterpressures | too far down the standpipe. | Before connecting the drain hose, | |
in the range of | If the end of your drain hose is fitted | remove any internal restrictions - | |
1000KPa).Mostcoldwatersupplies | with‘retainingflaps’,ensuretheyare | This will prevent a build up of debris | |
willbeinthisrange.NOTE:lowwater | insertedfullyintothestandpipe. This | which could cause a blockage. | |
pressure will lead to excessively | will prevent the pipe from jumping | Remove any restrictions from the | |
long fill times or no fill. | out during installation and use. | waste spigot and ensure that the | |
| sealingbungisremoved.Thehose | ||
is connected and the old hose is |
| should be routed, such that it is | |
disposed of safely. |
| raised to a minimum height of | |
- Ensure the fill hose is only fitted to |
| 800mm(31/2”). | |
the cold water supply. DO NOT |
|
| |
overtighten the hose connector, |
|
| |
hand tight is sufficient. |
|
| |
- Ensure the fill hose is not kinked. |
|
| |
- Tap connections (if applicable): A | DO NOT position the standpipe |
| |
range of adaptors are available to | near an electrical outlet. |
| |
suit your tap. | ENSURE that the drain hose is not |
| |
- DO NOT connect the dishwasher | kinked and it is routed as shown in |
| |
toasingleoutletinstantaneouswater | thediagram. | NOTE: Ensure the sink outlet | |
heater or an electric heater. |
| ||
| pipe has a minimum diamtere of | ||
| The standpipe should have a bore | ||
| 32mm. | ||
Drain hose connection. | of at least 38mm (11/2”). It should | ||
| |||
WARNING: Connect your | be installed as shown, have a trap |
| |
dishwasher drain hose to pipes | fitted and must discharge into the |
| |
which connect to the foul drain | same drain system as your |
| |
system and not to surface water | household sink. |
| |
drains. |
|
| |
IMPORTANT: For the correct | It MUST NOT be connected to a | 1. Untie the end of the GREY | |
operation of your dishwasher, it is | surface water drain. | ||
drainage hose from the rear of the | |||
essential to comply with the |
| ||
| appliance. | ||
following information: |
| ||
| 2. Reposition the ‘Hooked End | ||
|
| ||
|
| Support’ as required along the | |
|
| GREY drainage hose. | |
|
| 3. If fitting an under sink waste | |
|
| disposal unit, cut out the | |
|
| membrane, bung or blanking plug. |
Remember you will be charges for a service call is a problem with your appliance is caused by incorrect installation or misuse.
6