Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance. | GB | |||
|
|
|
| |
|
|
|
|
|
| Problem: | Possible causes / Solutions: |
|
|
| The dishwasher cannot be started or | • Switch off the appliance by pressing the ON/OFF button. Switch it back |
|
|
| on after approximately one minute and reset the program. |
|
| |
| controlled. | • The appliance has not been plugged in properly. |
|
|
|
| • The dishwasher door has not been shut properly. |
|
|
| The door won’t close. | • The lock was released. Strongly push the door until a “clacking” noise is |
|
|
| heard. |
|
| |
|
|
|
| |
| No water drains from the | • The dishwasher cycle has not finished yet. |
|
|
| • The water drain hose is bent (see Installation.) |
|
| |
| dishwasher. | • The drain duct is blocked. |
|
|
|
| • The filter is clogged up with food residues. |
|
|
|
| • The dishes are rattling against each other or against the sprayer arms. |
|
|
| The dishwasher is too noisy. | • An excessive amount of foam has been produced: the detergent has not |
|
|
| been measured out correctly or it is not suitable for use in dishwashers |
|
| |
|
|
|
| |
|
| (see |
|
|
| The dishes and glasses are | • The level of refined salt is low or the dosage setting is not suited to the |
|
|
| hardness of the water (see Rinse aid and salt.) |
|
| |
| covered in a white film or |
|
| |
| • The lid on the salt dispenser was not closed properly. |
|
| |
| limescale deposits. |
|
| |
| • The rinse aid has been used up or the dosage is too low. |
|
| |
|
|
|
| |
| The dishes and glasses are | • The rinse aid dosage is too high. |
|
|
| streaked or have a bluish tinge. |
|
| |
|
|
|
| |
|
| • A wash cycle without a drying cycle has been selected. |
|
|
| The crockery has not been dried | • The rinse aid has been used up or the dosage is too low (see Rinse aid |
|
|
| and salt.) |
|
| |
| properly. |
|
| |
| • The rinse aid setting is not suitable. |
|
| |
|
|
|
| |
|
| • The crockery is made from |
|
|
|
| • The racks are overloaded (see Loading the racks.) |
|
|
|
| • The crockery has not been arranged properly. |
|
|
|
| • The sprayer arms cannot move freely. |
|
|
|
| • The wash cycle is too gentle (see Wash cycles.) |
|
|
| The crockery is not clean. | • An excessive amount of foam has been produced: the detergent has not |
|
|
| been measured out correctly or it is not suitable for use in dishwashers |
|
| |
|
|
|
| |
|
| (see |
|
|
|
| • The lid on the rinse aid compartment was not shut correctly. |
|
|
|
| • The filter is dirty or blocked (see Care and maintenance.) |
|
|
|
| • The refined salt level is low (see Rinse aid and salt.) |
|
|
|
| • There is no water in the mains supply. |
|
|
| The dishwasher does not take any | • The water inlet hose is bent (see Installation.) |
|
|
| • Turn on the tap and the appliance will start after a few minutes. |
|
| |
| water in - Tap |
|
| |
| Beeps are heard * and the Washing |
|
|
|
| indicator light is flashing quickly. |
|
|
|
| Beeps are heard* and the Drying and End | • The appliance stopped because no action was taken when the beep |
|
|
| indicator lights are flashing quickly. | sounded*. |
|
|
| Switch off the machine using the ON/OFF button, turn on the tap and |
|
| |
|
|
|
| |
|
| switch the machine back on after a few seconds by pressing the same |
|
|
|
| button. |
|
|
*Only available in selected models.
15