Installation
Keep this instruction manual in a safe place for
EN | future reference. If the appliance is sold, given away or | |
| ||
| moved, please ensure the manual is kept with the | |
| machine, so that the new owner may benefit from the | |
| advice contained within it. | |
|
| Please read this instruction manual carefully: it |
|
| |
| contains important information regarding the safe | |
| installation, use and maintenance of the appliance. | |
|
| If the appliance must be moved at any time, keep it |
|
| |
| in an upright position; if absolutely necessary, it may be | |
| tilted onto its back. | |
|
| This appliance is intended to be used in household |
|
| |
| and similar applications such as: | |
| - staff kitchen areas in shops, offices and other working | |
| environments; | |
| - farm houses; | |
| - by clients in hotels, motels and other residential type | |
| environments; | |
| - bed and breakfast type environments. | |
Positioning and levelling
1.Remove the appliance from all packaging and check that it has not been damaged during transportation.
If it has been damaged, contact the retailer and do not proceed any further with the installation process.
2.Check the dishwasher by placing it so that its sides or back panel are in contact with the adjacent cabinets or
even with the wall. This appliance can also be recessed under a single worktop* (see the Assembly instruction
sheet).
3.Position the dishwasher on a level and sturdy floor. If the floor is uneven, the front feet of the appliance may be adjusted until it reaches a horizontal position (the angle of inclination must not exceed 2 degrees). If the appliance is levelled correctly, it will be more stable and much less likely to move or cause vibrations and noise while it is operating.
4*. Adjust the height of the rear foot from the front of the appliance* on the central lower part of the dishwasher, turning a hexagonal spanner (red color) with an opening of 8 mm in a clockwise direction to increase the height or in an anticlockwise direction to decrease the height.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation that may form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before running the first wash cycle, completely fill the salt dispenser with water and add only then approximately 1 kg of salt (see chapter entitled Rinse aid and refined salt). The water may overflow: this is normal and is not a cause for concern. Select the water hardness value (see chapter entitled Rinse aid and refined salt). - After the salt has been poured into the machine, the LOW SALT indicator light* switches off.
If the salt container is not filled, the water softener and the heating element may be damaged as a result.
Technical data
Dimensions | width 45 cm | |||
height 85 cm | ||||
|
|
| depth 60 cm | |
Capacity | 10 standard | |||
|
|
| ||
Water supply | 0,05 ÷ 1MPa (0.5 ÷ 10 bar) | |||
pressure | 7,25 psi – 145 psi | |||
|
|
| ||
Power supply | See appliance data plate | |||
voltage | ||||
| ||||
|
|
| ||
Total absorbed | See appliance data plate | |||
power |
| |||
Fuse | See appliance data plate | |||
|
|
| This dishwasher conforms to the | |
|
|
| following European Community | |
|
|
| Directives: | |
|
|
| ||
|
|
| ||
|
|
| Compatibility) | |
|
|
| ||
|
|
| 1275/2008) (Ecodesign) | |
|
|
| ||
|
|
| ||
|
|
| and Electronic Equipment | |
|
|
| (WEEE) | |
|
|
| ||
*Only available in selected models.
2
