Hotpoint SDW 60 How to use your Dishwasher, D Ishwasher, First of all, Modifying a wash cycle in

D ISHWASHER

How to use your Dishwasher

First of all.	Modifying a wash cycle in	You decide when it starts.	Cycle phase and delayed
- Turn on the water supply	progress.	When you have loaded the dishes,	start indicator light "G"
tap completely.	But if you have chosen the wrong	you can choose when to start your
- Add the correct amount of	cycle, not to worry! You can modify	dishwasherbeforesettingthewash	(1)	Flashing to indicate a
detergent.	the wash cycle in progress, if it has	cycle desired. Press button "D" to	delayed start, to remind you that
- Load the baskets correctly.	only just started. Keep the RESET	delay the start of the wash cycle by	you have set a delayed start.
- Check that the spray arms	button "R" pressed for about 5	12, 9, 6 or 3 hours. Each time you
rotate freely.	seconds: a prolonged beep will	press it, you will hear a short beep	(2)	On,litconstantly,eachlight
- Close the door securely.	sound, followed by three short	and the indicator light "G"	shows which stage of the wash
-After performing all the operations	beeps. Indicator light "G" will turn	corresponding to the selected	cycle is in progress.
	off and at this stage, all the settings	delay will light up.
described in the previous para-	will have been cancelled. You are	Now you can select the desired	Would you like to see
graphs, open the appliance door	now free to re-set the correct wash	wash cycle. Press the start button
and press ON-OFF button "A": in-	cycle.	"R"andafteryouhearthebeep,the	which settings you have
dicatorlight"B"comeson.Yourap-		countdown to the delayed start will	made?
pliance is now on and awaiting	You've left out a dish?	begin.	Atanytime,whenthecycleisunder
instructions.	Well, it happens to everyone. Inter-	Once this time is up, the indicator	way, if you press button "P", the
	rupt the wash cycle by pressing the	light will stop flashing and the wash	cycle in progress indicator light will
Select the wash cycle.	ON-OFFbutton,insertthedishyou	cycle will begin.	light up for a few seconds.
Select the wash cycle by pressing	had forgotten and press the ON-	If you have set a 12 hour delay, for
button "P". Each time this button is	OFF button again. The cycle will	example, once you have selected
pressed, one of the indicator lights	start up from where you interrupted	the wash cycle, the 12 hour
"E" will come on in sequence, se-	it.	indicator light will flash followed
lect the wash cycle most suitable		by the others in sequence until the	For your own safety,
for the type of dishes to wash (see	Cycle end	set time delay is up. A quick look at
‘Programme Chart’).	The end of the wash cycle is indi-	the indicator lights will keep you	ensure the door is closed
			when the dishwasher is
If the appliance door is shut, press	catedbyadoublebeepandtheflash-	informedofthecountdownprogress
			not in use.
the Start button "R" and you will	ing of the wash cycle indicator light	at all times.
hear a beep; the cycle will start up	"G".	Have you changed your
within a few seconds.	Open the dishwasher door, press
	the ON-OFF button cutting off the	mind?
The dishwasher informs	electricity supply to the appliance.	If you change your mind, you can
	Turn off the water tap.	set a shorter time delay: press but-
you.		ton "D" to select it. You need not
Your dishwasher has indicator	Wait a few minutes before unload-	reset the wash cycle.
lights "G" which light up to indicate	ing the dishes: they are very hot! If
the wash cycle phase that is	youwaitalittlewhile,theydrybetter	If on the other hand you want to
underway	due to the steam.	cancel the delay set and you want
	Empty the lower rack first.	the cycle to start immediately,
		pressbutton"D"repeatedlyuntilthe
	There's been a power	cycle starts and indicator light "G"
	failure or you opened the	corresponding to the cycle start
	dishwasher door	phase comes on.
	The wash cycle stops and then
	restarts when the electricity comes
	backonorwhenyouclosethedoor.

8