HP 516733B21 manual Firmware requirements, LEDs, Front Panel

switch CLI, accessing it via serial interface attached to OA and/or USB interface attached to the blade.

When using optional transceiver modules or direct attach cables, order the modules and cables separately. For more information, see the QuickSpecs on the HP website (http://www.hp.com/go/bladesystem/interconnects).

For more information on BladeSystem port mapping, see the HP BladeSystem enclosure setup and installation guide that shipped with the enclosure.

For the most current product information, see the release notes at http://www.hp.com/go/bladesystem/documentation.

Firmware requirements

Always install the most current firmware or software for the following items:

Port 17 consists of a CX4 port multiplexed with an SFP+ port. Only one may be active. The SFP+ port takes precedence: if it contains a module, it is the active port and the CX4 port is inactive.

Ports 23 and 24 are each multiplexed with inter-switch link ports on the blade switch’s backplane. Either the SFP+ port on the front panel or the backplane port can be active, but both can not be active at the same time. The SFP+ port on the frontplane takes precedence: if it contains a module, it is the active port and its corresponding backplane port is inactive. Refer to the Installation and Getting Started Guide for more information.

LEDs

Server blade system ROMs

Ethernet mezzanines

HP BladeSystem Onboard Administrator

HP ProCurve blade switch

For additional information on required firmware or software versions and to download firmware or software updates, see the HP website:

1.Go to http://www.hp.com/#Support.

2.Click the “Download drivers and software” radio button.

3.Enter “6120XG” in the text box and click “Go”.

4.Click the link for your operating system.

5.Download the appropriate software or firmware.

Front Panel

Item	Description
1	Port 17 (10GBASE-CX4) *
2	Console port (USB 2.0 mini-AB connector)
3	Clear button
4	Port 17 SFP+ (10-GbE) slot * †
5	Port 18 SFP+ (10-GbE) slot †
6	Port 19 SFP+ (10-GbE) slot †
7	Port 20 SFP+ (10-GbE) slot †
8	Port 21	SFP+ (10-GbE) slot †
9	Port 22	SFP+ (10-GbE) slot †
10	Port 23	SFP+ (10-GbE) slot * †
11	Port 24	SFP+ (10-GbE) slot * †
12	Reset button (recessed)

* Dual-personality port. See explanation below.

†Supports 10GBASE-SR SFP+, 10GBASE-LR SFP+, 10GBASE-LRM SFP+, 1000BASE-T SFP, 1000BASE-SX SFP, and 1000BASE-LX SFP pluggable optical transceiver modules.

Dual-personality ports

Item LED description

1Module locator (UID)

2Module status (health)

3Port 17 status (10GBASE-CX4)

4Port 17 activity (10GBASE-CX4)

5Port 17–22 status (SFP+ connector)

6Port 23–24 status

7Port 23–24 multiplexed port status

8Port 23–24 activity

9Port 17–22 activity

10Port 17 multiplexed port status

Status

Blue = Module ID selected Off = Module ID not selected

Green = Normal operation Amber = Fault

Off = Power off

Green = Port is connected to the network.

Amber = Fault

Off = Not connected Green flashing = Activity

Green = Port is connected to the network.

Amber = Fault

Off = Not connected

Green = Port is connected to the network.

Amber = Fault

Off = Not connected

Green = Frontplane port is active. Internal (backplane) link is inactive.

Off = Frontplane port is inactive. Internal (backplane) link may be active.

Green flashing = Activity Green flashing = Activity

Either the CX4 port or the SFP+ port may be active, but not both.

Green = Port is active. Off = Port is inactive.