Manuals / HP / Computer Equipment / Desktops

HP 6563Z (US), 6671 (LA), 6642D (US) Drive Specification, ST317221A, ST313021A, ST38410A, ST34313A

Models: 6573Z (US)

1 41

Page 11

4	U8 Family Product Manual, Rev. B

Drive Specification	ST317221A	ST313021A	ST38410A	ST34313A


Nonrecoverable read errors		1 per 1013 bits read
Mean time between
failures (power-on hours)	500,000

Contact start-stop cycles (25°C,
40% relative humidity)	50,000

SeaShield		Yes

Page 11

Image 11

HP 6563Z (US), 6671 (LA), 6642D (US), 6641 (LA), 6553 (US) manual Drive Specification, ST317221A, ST313021A, ST38410A, ST34313A

Contents

Ultra ATA Interface Drives U8 FamilyST317221A, ST313021A ST38410A, ST34313AUltra ATA Interface Drives U8 FamilyST317221A, ST313021A ST38410A, ST34313APage U8 Family Product Manual, Rev. B ContentsATA interface Configuring and mounting the driveFigures U8 Family Product Manual, Rev. B Introduction ST313021A Specification summary tableDrive Specification ST317221AST34313A Drive SpecificationST313021A ST38410AST38410A Drive SpecificationST317221A ST313021A1.2 Physical organization 1.0 Drive specifications1.1.1 Default logical geometry 1.1 Formatted capacity1.5 Seek time 1.4 Physical characteristicsDrive Specification 1.3 Recording and interface technology1.6 Start/stop times 1.7 Power specifications1.7.1 Power consumption Spinup powerIdle mode power Seek ModeRead/Write power and current Operating power and currentTypical Amps RMS Power Mode1.7.1.1 Typical current profile Typical WattsIdle mode 1.7.4 Power-management modesPower Modes Active modeIdle and Standby timers 1.8 Environmental tolerances 1.8.1 Ambient temperature1.8.2 Temperature gradient Sleep mode1.8.3 Humidity 1.9 Drive acoustics 1.8.6.1 Operating vibration1.8.6.2 Nonoperating vibration 1.12.2 Electromagnetic compatibility 1.12 Agency certification 1.12.1 Safety certification1.10 Electromagnetic susceptibility 1.11 ReliabilityAustralian CE-Tick N176 1.12.3 FCC verificationU8 Family Product Manual, Rev. B 2.1 Handling and static-discharge precautions 2.0 Configuring and mounting the driveCable select 2.2 Jumper settings 2.2.1 Master/slave configuration7 5 3 8 6 4 Options jumper block J8 Master or single drive Drive is slave2.3 Drive mounting 2.2.2 Cable-select option2.2.3 Ultra ATA/66 cable Note Dimensions are shown in inches mm Figure 3. Mounting dimensions-top, side and end view3.1 ATA interface signals and connector pins 3.0 ATA interfaceDrive pin # Figure 4. I/O pins and supported ATA signalsSignal name Host pin # and signal descriptionATA-standard commands 3.1.1 Supported ATA commandsCommand name Command code in hexCommand code in hex 3.1.2 Identify Drive commandValue WordDescription x.xxxxxxH xxxxHxxxxH xxxxHxxxxH WordDescription ValuexxxxH WordDescription xxxxHSet transfer mode based on value in Sector Count register 3.1.3 Set Features commandRegister 3.1.4 S.M.A.R.T. commandsCode in Features S.M.A.R.T. CommandRegister S.M.A.R.T. CommandCode in Features Page Page Publication Number SG35226-001, Rev. B, Printed in USA Seagate Technology, Inc920 Disc Drive, Scotts Valley, California 95066, USA