Parts List
Assembly Instructions
PART # | PART DESCRIPTION | QUANTITY | |
REQUIRED | Allen Wrench | Philips Screwdriver |
|
TOOLS |
| ||
9 | 34mm Cam Lock Connector Bolt | 10 | |
10 | 50mm Screw |
| 16 |
12 | 30mm Screw |
| 4 |
8 | Cam Lock |
| 10 |
NOTE: TWO PEOPLE ARE RECOMMENDED TO ASSEMBLE THIS TABLE.
1. Side Assembly
A. INSERT two Cam Locks (8) into each of the Side Support Panels (6). INSERT five Cam Lock Connector Bolts (9) into the Left Front Panel (4) and Right Front Panel (5).
B. INSERT a Glass Shelf Support Pin (11) into the center hole |
|
of each Side Support Panel (6). | 4,5 |
C. ATTACH each Front Panel (4 & 5) to each Side Support Panel (6) as shown in Fig. 1. TIGHTEN Cam Locks (8) with Philips Screwdriver, DO NOT OVERTIGHTEN.
2. Table Assembly
Fig. 1
6
9
8
11
11 | Glass Shelf Support Pin | 4 |
13 | Plastic Screw Caps | 8 |
4 (Left) | Left & Right Front Panels | 2 |
5 (Right) |
A. PLACE the Bottom Shelf (1) on a soft flat surface with the
facing up. INSERT four Cam Locks (8) into the large holes. Make sure the thread openings of the Cam Locks face toward the outside edge of the Bottom Shelf (1).
B. CAREFULLY TIP the Bottom Shelf (1) on the front (longer) edge so that the underside is facing away from you. ALIGN the edges of the Side Panels (6) and Bottom Shelf and INSERT the Cam Lock Connector Bolts (9) into the Cam Locks (8). SECURE the Side Panels (6) to the Bottom Shelf by tightening the Cam Locks with the philips screwdriver, DO NOT OVERTIGHTEN. INSERT two
50mm Screws (10) through the predrilled holes in the Bottom Shelf andFig. 2 into the Side Panels (6) and tighten.
6 | Side Support Panels | 2 |
| Rear Support Panel |
|
C. CAREFULLY TIP the unit upside down and SECURE the Rear Support Panel (3) to the table bottom using four Screws (10).
D. CAREFULLY TIP the partially assembled table over so that it is sitting upright on the floor. PLACE two Shelf Support Pins (11) into the holes in the rear panel as shown in
Fig. 2. Make sure the rubber pads are facing up.
10
13 
2
3 | with Cable Management | 1 |
2 | Top Shelf | 1 |
E. PLACE the Glass Shelf (7) into the partially assembled table and onto the four Shelf Support Pins (11) as shown in Fig. 2.
6
8
3
7 | Glass Shelf | 1 |
1 | Bottom Shelf | 1 |
F. PLACE the Top Shelf (2) onto partially
assembled table. INSERT the Cam Lock |
| |
Connector Bolts (9) in the Front Panels |
| |
(4,5) into the Cam Locks (8) in the Top | 4 | |
Shelf and turn Cam Locks to tighten. DO | ||
9 | ||
NOT OVERTIGHTEN. SECURE Top Shelf | ||
|
using eight 50mm Screws (10).
11
7 | 8 | 6 |
FOR YOUR SAFETY, PLEASE FOLLOW THESE PRECAUTIONS:
!ALWAYS REMOVE THE TV AND OTHER EQUIPMENT FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED UNIT.
!BE CAREFUL WHEN MOVING THE ASSEMBLED FURNITURE AFTER THE GLASS SHELF HAS BEEN INSTALLED, AND/OR WHEN THERE IS EQUIPMENT LOCATED ON THE FURNITURE AS THIS MAY CAUSE THE SHELF TO BECOME UNSECURED AND FALL.
!WHEN IN USE, THIS FURNITURE MUST BE PLACED ON A FLAT, SOLID AND LEVEL SURFACE.
! DO NOT LEAN ON THE TV WHEN IT IS ON THE TV STAND. ! DO NOT CLIMB OR STEP ON THE STAND.
!DO NOT BANG OR PLACE YOUR OWN WEIGHT ON THE GLASS SHELF.
!DO NOT PLACE ITEMS ON THE SHELVES WHICH EXCEED THE MAXIMUM WEIGHT LIMITS OF 200 LBS. FOR TOP SHELF AND 50 LBS. FOR GLASS SHELF
G. INSERT eight Plastic Screw Caps (13) | 1 | |
over the Screws (10) which were inserted | ||
| ||
into the Top Shelf (2), as shown in Fig. 2. | 10 | |
|
FOR YOUR SAFETY, SECURE THE TV TO
THE TABLE FROM BENEATH THE THE TOP SHELF8 USING 4 OF THE SUPPLIED 30MM BOLTS (PART #12)
NOTE: THE MIDDLE GLASS SHELF (7) CAN NOT BE REMOVED ONCE THE TOP SHELF (2) IS SECURED, BUT IT CAN SHIFT OR TIP FORWARD WHEN THE TABLE IS MOVED OR IF THE SHELF SUPPORT PINS (11) ARE NOT PLACED SECURELY IN THEIR HOLES WITH THE RUBBER PADS FACING UPWARDS. ALWAYS PLACE HEAVIEST COMPONENTS ON LOWER SHELF.
5
10 
8
