Hubbell UE28 Cable Removal, Cable Installation, Collector Replacement, Electrical Connections

CABLE REMOVAL

Use the following procedure to remove worn or damaged cable from reel prior to installation of new cable.

CAUTION

Failure to relieve all spring tension prior to removing cable could result in damage to equipment or personal injury. Follow instructions carefully.

1.Move machine serviced by reel to a position closest to reel. Springs will still be under pre-tension at this point.

2.Turn off all electric power.

3.Lock spool to prevent turning using either a spool lock mechanism or by tying off.

4.Disconnect cable from machine junction box.

5.Grip spool by hand and carefully release spool lock or tie. Slowly unwind remaining tension.

6.Again lock or tie spool to prevent rotation.

7.Remove cable from spool. Loosen cable clamp and water-tight connector. Disconnect conductors from slip ring and remove cable.

8.Install new cable following instruction at right.

CABLE INSTALLATION

Use the following procedure to replace cable or if reel was ordered without cable. Refer to ELECTRICAL CONNECTIONS DRAWING, below.

1.Unspool new cable from shipping spool and lay out to eliminate twist.

NOTE: This step is not essential, but will aid in winding operation of the reel and prolong cable life.

2.Feed one end of the cable through water-tight connector on the spool hub inside the spool and into the slip ring.

(See drawing below).

NOTE: This may require that jacket of cable be stripped to allow conductors to pass through shaft.

3.Connect individual conductors to appropriate rings on collector using crimp fitting or similar connection method.

4.Tighten water-tight connector. Place cable clamp on cable and securely fasten to spool disk.

5.Wind the cable onto the reel spool by hand rotating spool in direction it turns free of spring tension.

6.Connect free end of cable to machine junction box.

7.Pretension reel and complete installation as previously described.

COLLECTOR REPLACEMENT

1.Turn off all power to reel.

2.Remove collector cover and gasket.

3.Disconnect electric leads to and from collector.

4.Remove button plug from hole in side of housing. Insert long 1/8” Allen wrench through hole and loosen two set screws in collector locking collar Set screws are at 90O to one another..

5.Slide collector off shaft.

6.Install new collector by reversing above steps.

ELECTRICAL CONNECTIONS

LEADWIRE INPUT FIXED END (CUSTOMER SUPPLIED)

CABLE LEADWIRES MOVING END

CABLE

NOTE:

Wire size, wire connectors, connection sequence,

CABLE CLAMP

and connection methods must comply with National Electrical code and Local Electrical ordi- nances. If in doubt, contact a local electrical con-

BRUSH TERMINAL
CONNECTIONS
SLIP-RING
LEADWIRES ARE
NUMBER TAGGED				SET
1	2	3	4
				SCREW
SLIP-RING LEAD TO
MOVING CABLE
CONNECTIONS
1	2	3		4
	SLIP–RINGS
				COLLAR

SPOOL

HUB

SPOOL

DISK

WATER–TIGHT

CABLE CONNECTOR

FRAME

tractor or electrical inspector.

COLOR SEQUENCE FOR TYPE SO CABLE

THREE CONDUCTOR CABLE

#1 – BLACK

#2 – WHITE

#3 – GREEN (ground)

FOUR THRU TWELVE CONDUCTOR CABLE

# 1 – BLACK

# 2 – WHITE

# 3 – RED

# 4 – GREEN (ground)

# 5 – ORANGE

# 6 – BLUE

# 7 – WHITE W/ BLACK TRACER

# 8 – RED W/ BLACK TRACER

# 9 – GREEN W/ BLACK TRACER

#10 – ORANGE W/ BLACK TRACER

#11 – BLUE W/ BLACK TRACER

SLIP–RING ENCLOSURE

•600 VOLT AC. 250 VOLT DC. WATERTIGHT, DUST TIGHT.

•DO NOT EXCEED AMPERAGE RATING OF CABLE OR SLIP RING.

•NUMBER OF CIRCUITS MAY VARY FROM TWO (MINIMUM) TO 36 (MAXIMUM). FOUR CIRCUITS SHOWN.

#12 – BLACK W/ WHITE TRACER

HUBBELL

	®	GLEASON REEL CORP.
		P.O. Box 26 • 600 South Clark St.
		Mayville, WI 53050–0026
®		Phone 920–387–4120 • Fax 920–387–4189
	A Hubbell Company

Printed in USA Bulletin No. 045396.a