ENGLISH INSTRUCTIONS
IMPORTANT! WRITE DOWN MODEL NUMBER FROM BOX ON PAGE 1 OF THIS OWNERS MANUAL
1.Remove contents from tank (1).
2.Correctly identify each pole section and mark indicated distance from ends with tape as shown.
3.IMPORTANT! Center alignment slot of middle pole section (5) in a lower hole of top pole section (4) as shown. While maintaining alignment, bounce pole top (4) and middle section (5) together as shown until they no longer move toward taped reference mark. Upright assembly. NOTE: Pole sections should have a
4.IMPORTANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 4. While maintaining alignment, bounce assembly and lower section (6) together as shown until they no longer moved toward taped reference mark.
NOTE: Pole sections should have a
5.Install rod (7) through holes in bottom pole (6) section and eyebolt (8).
6.Install wheel axle (2) through wheel carriage (9) and install wheels (3) onto wheel axle (3) with spacers (28) as shown. Insert pole assembly into tank assembly as shown.Secure bottom pole (6) to tank, lower bracket “A” (36) and wheel bracket as shown, a deep socket is recommended.
NOTE: Two people recommended for this step.
IMPORTANT! DO NOT OVER TIGHTEN.
7.Secure tank struts (13) to pole. Rotate
WARNING: TIGHTEN BOLT (11) IN LOCK NUT (14) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE.
8.Secure
WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY.
9.Mount brackets (20), rim spacer (45) and rim (18) to backboard and finger tighten. NOTE: Final adjustments will be made in Step 12. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware.
10.Support pole and tank assembly over support table. Carefully slide backboard components onto pole.
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY.
WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN EMPTY, MAY TIP OVER.
11.While still in the horizontal position, secure hardware at desired position as shown and tighten all hardware completely at this time.
12.Install netclips and net as instructed on illustration page.
13.NOTE: Two people recommended for this procedure. Carefully upright assembly. Apply moving system label (15) to front of pole as shown. Regulation rim height is 10 feet (3.05 m).
WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED WHEN EMPTY, MAY TIP OVER.
14.Place assembled unit to desired location. Fill tank with water (30 gallons (114 liters)) or sand (360 lb. (163 kg)) and snap tank cap (30) in place. Insert
(29) onto tie down stake (27).
IMPORTANT! Add two gallons (7.6 liters) of
15. Slide framework halves into net and insert reduced end of frame into expanded end as shown.
NOTE: TABS ON STRAPS SHOULD BE POSITIONED ON THE OUTSIDE
OF NET. FIT OF NET MAY BE TIGHT TO FRAME
16.Attach upper brackets (38) to framework with bolts (39 ), nuts (17) and washers (12) as shown.
17.Attach lower bracket “B” (37) to framework with bolts (39), nuts (17) and washers (12) as shown.
18.Lift net assembly into place and attach to unit with hand knobs (41) , (42) as shown.
19.Install fiberglass rods (33) into pockets on net. Top and bottom ends of rods are inserted into holes on framework. Attach pole pad as shown.
20Attach snap clips on tarp to “D” ring on net as shown.
Thread straps on net through tarp as shown and tighten straps to desired tarp tension.
WARRANTY CARD:
Please remember to complete your product registration form either
3 | 02/04 | P/N 211583 |
