Refilling the Water Tank
1.When the water tank level is low, turn the humidifier ‘OFF’, and unplug.
2.Remove the tank and take it to the sink or tub to refill.
3.Turn the tank upside down and unscrew the tank cap by turning it counterclockwise. Empty the tank, refill with fresh cool water (never use hot water), and replace the tank cap.
Be sure not to overfill the tank as water damage may occur to furniture or flooring due to spillage.
HUNTER WILL NOT ACCEPT RESPONSIBILITY FOR DAMAGE TO PROPERTY CAUSED BY WATER SPILLAGE.
4.Carry the tank back to the humidifier. Turn the tank upright and place it on the humidifier. Be sure that the tank is seated properly in the base. If the tank is properly located on the base, you will see air bubbles flowing up into the tank.
5.Place the full tank on the unit and allow the water to fill the bottom tray. The water is at the proper level in the bottom tray when the tank stops bubbling. Run the unit on “HI” speed for 11⁄2 minutes for optimum pump operation. Set the unit to the desired speed.
Cleaning the Humidifier
Many regions have hard water with high concentrations of minerals. When water evaporates from The Care Free® Evaporative Humidifier, minerals may be left behind. These minerals can form a hard white scale which can be removed by following the cleaning instructions. The frequency of cleaning due to mineral build up can vary depending upon the quality of water you may have. Refer to Figure 1 for part names.
1.Turn the humidifier ‘OFF’ and unplug the unit.
2.Lift the main housing and remove the PermaWick Filter
Frame containing the PermaWick™ Filter. The motor is attached to the main housing. Do not place the motor near water. Do not use a wet towel on the motor or motor housing as electrical shock may occur.
3.The PermaWick™ Filter should be cleaned in a vinegar and water solution to remove any mineral buildup. Place in a solution of one (1) gallon of water and eight (8) ounces of undiluted white vinegar. Allow the filter to soak for 20 minutes.
4.After soaking, rinse it several times with clean water. Place the PermaWick™ Filter in a location where it can drip dry while you clean the other parts of your humidifier.
5.Remove the water tank from the base and empty any water that is left in the tank. Soak the base in a mixture of one
(1) gallon of water and eight (8) ounces of vinegar for 20 minutes.
6.After soaking, wipe the base with a soft cloth or sponge to remove any mineral build up. Rinse with clean water several times. If you are planning on storing the humidifier, be sure
the base is completely dry.
7.Fill the water tank with one (1) gallon of water and eight ounces of undiluted white vinegar. Replace the tank cap and shake the tank vigorously until all interior surfaces of the tank have been exposed to the water/vinegar mixture.
8.Empty the tank of the water/vinegar mixture. Rinse it several times with clean water and then replace the tank cap. If you are planning on storing the humidifier, dry it inside and out, leaving the cap off to allow the tank to completely dry. Continue to clean the other parts of your humidifier.
9.Remove the water diffuser cap by squeezing the two tabs as shown in Figure 3. Rinse the cap in clean water to remove any debris. If the cap contains hard water residue, soak it in a mixture of one (1) quart of water and two (2) ounces of vinegar for 20 minutes. Rinse well and reinstall the water diffuser cap. Do not expose motor or other electrical components to water.
10.Wipe the surfaces of the main housing with a soft cloth.
11.Once all the parts are clean, reassemble the humidifier, and follow the USING YOUR HUMIDIFIER instructions to continue use. If you are storing the humidifier, make sure the parts are completely dry, reassemble, and store in a dry location.
Tab
Water Diffuser Cap | Tab |
|
Figure 3
©2008 HUNTER FAN CO. | 4 | ||
|
|
|
|
|
|
|
|
|
|
|
|
