Comprehensive Maintenance Guide for Husqvarna Chainsaws 343FR and 345RX

MAINTENANCE

Carburetor

Your Husqvarna product has been designed and manufactured to speciﬁcations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in.To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, ask your dealer/service workshop (who will have a rev counter at their disposal) to adjust your carburettor.

WARNING! The complete clutch cover and

!shaft must be ﬁtted before the machine is started, otherwise the clutch can come loose and cause personal injury.

Carburetor adjustment

The carburettor can be designed in different ways, depending on the existing environmental and emissions legislation. Some machines are equipped with movement limiters on the carburettor’s adjuster screws. These limit the adjustment range to a maximum of 1/2 turn.

1/2

Function

•The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. The air/ fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine.

•The setting of the carburetor means that the engine is adapted to local conditions, for example, the climate, altitude, fuel and the type of 2-stroke oil.

•The carburetor has three adjustment controls: L = Low speed jet

H = High speed jet

T = Idle adjustment screw

•The L and H-jets are used to adjust the supply of fuel to match the rate that air is admitted, which is controlled with the throttle. If they are screwed clockwise the air/fuel ratio becomes leaner (less fuel) and if they are turned anti- clockwise the ratio becomes richer (more fuel). A lean mixture gives a higher engine speed and a rich mixture gives a lower engine speed.

•The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed.

Basic setting

•The basic carburetor settings are adjusted during testing at the factory. The basic setting is richer than the optimal setting and should be maintained for the ﬁrst few hours the machine is in use. The carburettor should then be ﬁnely adjusted. Fine adjustment should be carried out by a skilled technician.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops.

Rec. idle speed 2700 rpm

Recommended max. speed: See the Technical data section.

WARNING! If the idle speed cannot be

!adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

Fine adjustment

When the machine has been ”run-in” the carburetor should be ﬁnely adjusted. The ﬁne adjustment should be carried out by a qualiﬁed person. First adjust the L-jet, then the idling screw T and then the H-jet.

Conditions

•Before any adjustments are made, make sure that the air ﬁlter is clean and the air ﬁlter cover is ﬁtted. If you adjust the carburettor when the air ﬁlter is dirty it will result in a leaner mixture when the ﬁlter is ﬁnally cleaned. This can lead to serious engine damage.

•Carefully turn both jets, L and H, so that they are midway between fully screwed in and fully screwed out.

•Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

•Now start the machine according to the starting instructions and let it warm up for 10 minutes.

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti-clockwise until the cutting attachment stops.

Low speed jet L

Try to ﬁnd the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/ 4 turn counter-clockwise.