Husqvarna 346XP, 353 manual Bar and chain combinations, Bar Chain

TECHNICAL DATA

Bar and chain combinations

The following combinations are CE approved.

	Bar		Chain
Length,	Pitch,	Max.
inches	inches	tip radius
13	0,325	10T	Husqvarna H30
15	0,325	10T	Husqvarna H30
16	0,325	10T	Husqvarna H30
18	0,325	10T	Husqvarna H30
13	0,325	10T	Husqvarna H25
15	0,325	10T	Husqvarna H25
16	0,325	10T	Husqvarna H25
18	0,325	10T	Husqvarna H25
20	0,325	12T	Husqvarna H25

									L
				1
				5
Type	Inch	Inch/mm	Inch/mm	Degree	Degree	Degree	Inch/mm	Inch/cm: dl
H30	0,325"	0,050"/1,3	3/16" /4,8	85°	30°	10°	0,025"/0,65	13"/33:56	15"/38:64
								16"/40:66	18"/45:72
H25	0,325"	0,058"/1,5	3/16" /4,8	85°	30°	10°	0,025"/0,65	13"/33:56	15"/38:64
								16"/40:66	18"/45:72
								20"/50:78

EC-declaration of conformity (Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the chain saws Husqvarna 345, 346XP and 353 from 2002's serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the requirements of the COUNCIL'S DIRECTIVES:

-of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.

-of May 3, 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data.

The following standards have been applied: EN292-2, CISPR 12:1997, EN608.

Notified body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out EC type examination in accordance with the machinery directive's (98/37/EC) article 8, point 2c. The certificates for EC type examination in accordance with annex VI, have the numbers: 404/00/795 – 345 TAC, 404/00/794 – 346XP/G TAC, 346XP/G E-tech TAC, 404/02/899 - 353/G TAC, 353/G E-tech TAC.

In addition, SMP, Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has certified conformity with annex V of the Council's Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certificates have the numbers: 01/161/001– 345 TAC, 01/161/002 – 346XP/G TAC, 01/161/003 – 346XP/G E-tech TAC, 01/161/045

–353/G TAC, 01/161/046 - 353/G E-tech TAC.

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna August 29, 2002

Bo Andréasson, Development manager

English – 35