Fuel Handling

Fuel

Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two- stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

WARNING! Always ensure there is adequate

!ventilation when handling fuel.

Gasoline

•Use good quality unleaded gasoline.

•CAUTION! Engines equipped with catalytic converters must be run on unleaded fuel mixtures.

•Leaded gasoline will destroy the catalytic converter and it will no longer serve its purpose. The green fuel cap on saws ﬁtted with catalytic converters means that only unleaded gasoline can be used.

•The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two- stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor).

Running-in

Avoid running at a too high speed for extended periods during the ﬁrst 10 hours.

Two-stroke oil

•For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two stroke-engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) for all engines.

Gasoline, litre	Two-stroke oil, litre

	2% (1:50)

5	0,10

10	0,43/0,20

15	0,30

20	0,40

US gallon	US ﬂ. oz.

1	2 1/2

2 1/2	6 1/2

5	12 7/8

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by ﬁlling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before ﬁlling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

•We recommend the use of special oil (chain oil) with good adhesion characteristics.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

•In temperatures below 32°F (0°C) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your service agent when choosing chain oil.

18 – English

372XP EPA II, 365 EPA I specifications

The Husqvarna 365 EPA I and 372XP EPA II are two powerful chainsaws designed for serious woodcutting enthusiasts and professionals alike. Known for their robust performance, advanced technologies, and ergonomic design, these models are built to handle demanding tasks with ease.

The Husqvarna 365 EPA I is celebrated for its reliability and efficiency. It features a high-performance X-Torq engine that reduces fuel consumption by 20% and emissions by 75%, making it an environmentally friendly choice. The engine delivers impressive power output, ensuring that the saw can tackle tough cuts without compromising performance. Weighing in at just over 12 pounds, the 365 provides a perfect balance of power and maneuverability.

One of the standout features of the 365 is its Air Injection centrifugal air cleaning system, which helps to keep the air filter cleaner for longer periods. This results in reduced maintenance and improved performance, allowing users to focus on their cutting tasks rather than worrying about frequent cleaning. The chainsaw is also equipped with an adjustable oil pump, providing the user with the ability to control lubrication for better chain life and efficiency.

On the other hand, the Husqvarna 372XP EPA II takes performance to the next level. It boasts a larger displacement engine than the 365, offering enhanced power for professional applications. With the same X-Torq technology, it combines power and fuel efficiency, making it a great tool for heavy-duty tasks such as felling large trees or bucking heavy logs.

The 372XP is designed with an emphasis on ergonomics, featuring a slim body and excellent weight distribution. This makes it comfortable to handle, even during prolonged use. The chainsaw also comes with an innovative Smart Start system, which reduces resistance in the starter cord, ensuring easier starts every time. The adjustable oil pump feature is retained, allowing for precision control over the amount of oil delivered to the chain.

Both models reflect Husqvarna's commitment to quality and innovation, featuring durable components built to withstand the rigors of professional use. With their combination of advanced engine technology, design ergonomics, and ease of use, the Husqvarna 365 EPA I and 372XP EPA II remain top choices among chainsaw users looking for reliable performance and longevity. Whether you're a seasoned professional or a dedicated amateur, these chainsaws provide the power and efficiency necessary for a wide range of cutting tasks.

Husqvarna 365 EPA I, 372XP EPA II manual Fuel Handling

Models: 372XP EPA II 365 EPA I

FUEL HANDLING