Wheels / Decals, Repair Parts | Husqvarna 8527SBEB instruction

REPAIR PARTS

WHEELS / DECALS

SNOW THROWER - MODEL NO. 8527SBEB (96193001100), PRODUCT NO. 961 93 00-11

KEY	PART
NO.	NO.	DESCRIPTION

1532 18 78-33 Wheel Assembly, 16", LH

2532 15 54-43 Pin, Klik 1/4

3532 18 78-65 Wheel Assembly, 16", RH

4	532 14 63-15	Screw, Hex Head 5/16-18 x 5/8
5	532 17 98-30	Bearing, Axle

6532 17 46-97 Washer, Thrust (1")

KEY	PART
NO.	NO.	DESCRIPTION

1532 18 10-38 Decal, Danger

2532 19 13-76 Decal, Husqvarna

3532 18 10-34 Decal, Danger, Deﬂector

4532 18 10-41 Decal, Danger

5532 19 85-89 Decal, Husqvarna, 8527SBEB

6532 18 10-32 Decal, Instruction

7532 15 57-98 Decal, Traction Lever

8532 15 58-00 Decal, Auger Lever

9532 18 10-36 Decal, Speed Control

10	532 18 37-29	Decal, Remote Deﬂector
13	532 15 57-94	Decal, Husqvarna, Crown
- -	532 40 37-57	Owner’s Manual

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

31

Image 31

Husqvarna owner manual Wheels / Decals, Repair Parts, SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO

Contents

8527SBEB Operation Safe Operation Practices for Walk-Behind Snow ThrowersTraining Preparation CUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and Storage PARTS PACKED SEPARATELY IN CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTON INSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigCHECK TIRE PRESSURE KNOW YOUR SNOW THROWER OPERATION Drive speed control lever - used to select forward or MEETS A.N.S.I. SAFETY REQUIREMENTS TO USE THROTTLE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE FUEL SHUT-OFF VALVE See Fig TO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigCLEAN-OUT TO THROW SNOW See Fig CHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BAR BEFORE STOPPING SNOW THROWING TIPSIF RECOIL STARTER HAS FROZEN LUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USE AUGER GEAR CASE CLEANINGENGINE V-BELTS 3. Make sure the augers and all moving parts have completely stopped SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHT TO REPLACE BELTS See Fig CARBURETOR STORAGEOTHER TO REMOVE WHEELS See Fig Engine idles or TROUBLESHOOTINGLoss of power Does not start SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY AUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTSSNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CONTROL PANEL / DISCHARGE CHUTE CONTROL PANEL / DISCHARGE CHUTE HANDLES HANDLES DRIVE DRIVE SNOW THROWER - MODEL NO. 8527SBEB 96193001100, PRODUCT NO CHASSIS / ENGINE / PULLEYS DESCRIPTION PART532 1 13 WHEELS / DECALS WHEELS / DECALS ANR AVSQ UH STATEMENTWARRANTY532 40 37-57 Rev. 1 12.21.05 BY 2002