Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!!
YOUR SAFETY IS INVOLVED.
WARNING: In order to prevent accidental starting when setting up, transporting, ad- justing or making repairs, always disconnect spark plug wire and place wire where it cannot come in contact with plug.
WARNING: Engine exhaust, some of its constituents, and certain vehicle compo- nents contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
CAUTION: Muffler and other engine parts become extremely
hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.
I. GENERAL OPERATION
• Read, understand, and follow all |
| instructions on the machine and in the |
| manual(s) before starting. Be thoroughly |
| familiar with the controls and the proper |
| use of the machine before starting. |
• | Do not put hands or feet near or under |
| rotating parts. Keep clear of the dis- |
| charge opening at all times. |
• Only allow responsible individuals, who |
| are familiar with the instructions, to |
| operate the machine. |
• | Clear the area of objects such as rocks, |
| toys, wire, bones, sticks, etc., which could |
| be picked up and thrown by blade. |
• | Be sure the area is clear of other people |
| before mowing. Stop the machine if |
| anyone enters the area. |
•Do not operate the mower when bare- foot or wearing open sandals. Always wear substantial foot wear.
•Do not pull mower backwards unless abso- lutely necessary.Always look down and be- hind before and while moving backwards.
•Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may richochet back toward the operator. Stop the blade when crossing gravel surfaces.
•Do not operate the mower without prop- er guards, plates, grass catcher or other safety protective devices in place.
•See manufacturer’s instructions for proper operation and installation of accessories. Only use accessories ap- proved by the manufacturer.
•Stop the blade(s) when crossing gravel drives, walks, or roads.
•Stop the engine (motor) whenever you leave the equipment, before cleaning the mower or unclogging the chute.
•Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catcher.
•Mow only in daylight or good artifi cial light.
•Do not operate the machine while under the influence of alcohol or drugs.
•Never operate machine in wet grass. Always be sure of your footing: keep a firm hold on the handle; walk, never run.
•Disengage the self-propelled mech- anism or drive clutch on mowers so equipped before starting the engine.
•If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibra- tion is generally a warning of trouble.
•Alwayswearsafetygogglesorsafetyglass- es with side shields when operating mower.
II. SLOPE OPERATION
Slopes are a major factor related to slip & fall accidents which can result in severe injury. All slopes require extra caution. If
(Includes Muffl er Gasket, |
Exhaust Studs and |
Flanged Lock Nuts) |
HEAD / VALVE / BREATHER
KEY PART
NO. NO. DESCRIPTION
1 14 017 01-S Valve, Intake
214 016 01-S Valve, Exhaust
314 841 04-S Kit, Head Gasket (Includes Key Number 6 and Muffler Gasket)
424 072 06-S Stud, M6 x 1.0 x 93
514 318 01-S Kit, Cylinder Head (Includes Key Numbers 4 and 16)
614 041 05-S Kit, Carburetor Gasket
714 755 02-S Kit, Valve Train (Includes Key Numbers 1, 2, 8–12, Valve Stem Seal, Valve Springs, Push Rod Guide Plate, Cylinder Head Dowels and Push Rods)
814 186 02-S Arm, Rocker
914 599 01-S Pivot, Rocker Arm
1014 100 01-S Nut, Hex, Jam
1114 072 02-S Stud, Rocker Arm
1214 018 02-S Retainer, Valve Spring
1314 041 01-S Gasket, Valve Cover
1414 096 05-S Kit, Valve Cover (In- cludes Key Number 13)
1525 086 140-S Screw, Flanged,
M8 x 1.25 x 55
16 14 072 06-S Kit, Exhaust Hardware (Includes Muffl er Gasket, Exhaust Studs and Flanged Lock Nuts)
4 14 237 04-S Clamp, Hose |
5 25 111 34-S Line, Fuel
(24” - Cut To Length)
625 086 275-S Screw, Shoulder
714 268 04-S Diaphragm Assembly
814 041 05-S Kit, Carburetor Gasket (Includes Carburetor Heat Shield Gasket and Air Cleaner Base Gasket)
914 237 05-S Clamp, Hose
1014 853 27-S Kit, Carburetor, with Gaskets (Includes Key Number 8)
1114 112 02-S Spacer, Carburetor
1224 072 06-S Stud, M6 x 1.0 x 93
13M-641060-S Nut, Flanged, M6 x 1.0
1414 187 01-S Arm Assembly
1525 086 277-S Screw, Thread Forming (M4)
Not Illustrated:
-- 14 757 01-S Kit, Carburetor Repair (Includes Key Number 8)
CRANKCASE
KEY PART
NO. NO. DESCRIPTION
114 050 01-S Kit, Breather Filter (Includes Breather Cover Gasket, Breather Cover Spring, Breather Filter and Breather Reed)
214 032 02-S Seal, Oil
314 032 04-S Seal, Oil
4 17 030 12-S Bearing, Ball
514 380 06-S Dowel, Cylinder Head
614 018 03-S Retainer, Piston Pin
714 067 01-S Connecting Rod