Assembly / Pre-Operation | Husqvarna 927SBEXP instruction

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING

TRACTION

DRIVE

CONTROL

ROD

DRIVE

CONTROL

BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING

AUGER

CONTROL

BRACKET

FIG. 6

6

Image 6

Husqvarna 927SBEXP owner manual Assembly / Pre-Operation, INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and

Contents

927SBEXP Owners Manual Preparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining Operation Maintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES PARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER INSTALL SPEED CONTROL ROD See Figs. 1 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWER MEETS A.N.S.I. SAFETY REQUIREMENTS TO USE FUEL SHUT-OFF VALVE See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE THROTTLE CONTROL See Fig TO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO MOVE FORWARD AND BACKWARD See Fig SCRAPER BAR BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig CHECK ENGINE OIL LEVEL See Fig SNOW THROWING TIPS BEFORE STOPPINGIF RECOIL STARTER HAS FROZEN BEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATION V-BELTS CLEANINGENGINE AUGER GEAR CASE TO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key 3. Make sure the augers and all moving parts have completely stopped TO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig STORAGEOTHER CARBURETOR Does not start TROUBLESHOOTINGLoss of power Engine idles or REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLYSNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 532 17 CONTROL PANEL / DISCHARGE CHUTE REPAIR PARTS HANDLES 15 11 REPAIR PARTS DRIVE 35 33 REPAIR PARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 PART DESCRIPTION WHEELS / DECALS 1 13 532 40 SIEIT ILIB SON PSE RR EMO STUC 5ON ITC ES RANTYWAR TEMENTSTA2002 23-81 ONITA REID SCON YTN ARR AW INTA BO TOE RUD EROC P6 ONITC ES