Install Mower and Drive Belt | Husqvarna GTH26K54T specification

ASSEMBLY

ASSEMBLE FRONT WHEEL TO MOWER (See Fig. 3)

•Using shoulder bolt, washer and locknut from parts bag, assemble front wheel to mower as shown.Tighten securely.

FIG. 3

INSTALL MOWER AND DRIVE BELT

(See Figs. 4-12)

See MOWER AND DRIVE BELT ASSEMBLY Supplement Sheet for additional guidance on this assembly.

Be sure tractor is on level surface and engage parking brake.

•Lower attachment lift lever to it's lowest position.

CAUTION: Lift lever is spring loaded.Have a tight grip on lift lever, lower it slowly and engage in lowest position.

•Turn steering wheel to the left as far as it will go and position mower on right side of tractor with deﬂector shield to the right.

02965

FIG. 4

•Remove plastic tie securing belt, bring belt forward and check belt for proper routing in all mower pulley grooves.

A

FIG. 5

NOTE: Be sure mower side suspension arms (A) are point- ing forward before sliding mower under tractor.

•Slide mower under tractor until it is centered under tractor.

•FIRST INSTALL ANTI-SWAY BAR (S).

-From right side of mower, insert anti-sway bar into hole in transmission bracket (T).

T	S
A
	02995

FIG. 6

-Pivot bar towards you and insert other end of bar into hole in rear mower bracket (D). Move mower as needed to insert bar.

-Secure with washer and retainer spring as shown using small 5/16 retainer spring.

D

02996

FIG. 7

7

Image 7

Husqvarna GTH26K54T owner manual Install Mower and Drive Belt, First Install ANTI-SWAY BAR S

Contents

GTH26K54T II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General Operation IV. Towing ServiceGeneral Service III. Children Table of Contents Mower Mower Front Wheel Unassembled Parts Unpack Carton AssemblyTools Required for Assembly To Remove Tractor from Carton First Install ANTI-SWAY BAR S Install Mower and Drive Belt 7/16 Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL Belts Operation Reverse Operation System ROS on Position Know Your Tractor Stopping HOW to USE Your Tractor To USE Cruise Control -J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System Characteristics To Operate on Hills Service REMINDER/HOUR MeterUsing the Reverse Operation System Reverse Operation System ROS To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD Gasoline Mowing Tips Lubrication Chart MaintenanceBefore Each USE Tires BatteryTractor Brake Operation Engine Spark Plugs CleaningEngine OIL Filter Muffler To Remove Mower Service and AdjustmentsTo Install Mower Tractor See Fig Turn nut right Turn nut left To raise mower To Check Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Attach Jumper Cables To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See Fig To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust Carburetor Engine OIL StorageOther Fuel System Problem Cause Correction Troubleshooting Points Engine dies when Tractor Model NO. GTH26K54T 96043001100, Product no 43 Schematic Electrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive KEY Part NO. NO.DESCRIPTION Steering Assembly Engine Spark Arrester KIT Seat Assembly Wheels and Tires Decals Mower Deck KEY Part NO. NO.DESCRIPTION Mower Lift Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement