Husqvarna YTH2148XP - page 39

39

REPAIR PARTS

TRACTOR - MODEL NUMBER YTH2148XP (HAU21H48B), PRODUCT NO. 954 17 02-27

ENGINE

NOTE: All component dimensions given in U.S. inches

1 inch = 25.4 mm

1 532 17 81-47 Control Throttle

2 532 19 16-11 Screw 10 x 3/4 Single Lead Hex

3 - - - - - - - - Engine KAWA FH641

(Order Parts from Engine Manufacturer)

4 532 14 97-23 Mufﬂ er Asm Twin Lo-Tone

5 532 18 45-79 Exhaust Tube LH

6 532 18 45-80 Exhaust Tube RH

8 532 17 18-77 Bolt 5/16-18 unc x 3/4 W/Sems

10 532 14 66-29 Shield Browning

13 - - - - - - - - Gasket Mufﬂ er (Order from Engine Manufacturer)

14 532 14 84-56 Tube Drain Oil Easy

23 532 16 98-37 Shield Browning

25 532 19 15-96 Control Choke

29 532 13 71-80 Kit Spark Arrestor (Flat Scrn)

31 532 17 90-22 Tank Fuel

32 532 18 18-03 Cap Asm Fuel

33 532 12 34-87 Clamp Hose Blk

37 532 14 21-58 Line Fuel

38 - - - - - - - - Plug Drain Oil (Order from Engine Manufacturer)

41 532 13 92-77 Stem Tank Fuel

45 817 00 06-12 Screw Hexwsh Thdr 3/8-16 x 3/4

81 873 51 04-00 Nut Keps Hex 1/4-20 unc

101 532 18 43-62 Nut Flange M8-1.25

105 817 12 06-16 Screw 3/8-16 x 1

112 532 12 49-52 Bushing

KEY PART

NO. NO. DESCRIPTION

Contents

Main I. GENERAL OPERATION SAFETY RULES Safe Operation Practices for Ride-On Mowers II. SLOPE OPERATION SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Never IV. TOWING V. SERVICE TABLE OF CONTENTS PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES UNASSEMBLED PARTS Mower Gauge Wheels Seat Nose Roller TOOLS REQUIRED FOR ASSEMBLY TO REMOVE TRACTOR FROM CARTON UNPACK CARTON BEFORE REMOVING TRAC TOR FROM SKID ATTACH STEERING WHEEL (See Fig. 1) INSTALL SEAT (See Fig. 3) ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4) TO ROLL TRACTOR OFF SKID (See Op- er a tion section for location and function of con trols) TO DRIVE TRAC TOR OFF SKID (See Op- er a tion section for location and function of con trols) INSTALL MOWER AND DRIVE BELT (See Figs. 6 and 7) TO ATTACH NOSE ROLLER (See Fig. 5) CHECK TIRE PRESSURE CHECK MOWER LEV EL NESS CHECK FOR PROPER POSITION OF ALL BELTS CHECKLIST WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EX TRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS: Page KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE (See Fig. 8) TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8) TO USE THROTTLE CONTROL (See Fig. 8) TO USE CHOKE CONTROL (See Fig. 8) TO OPERATE ON HILLS TO TRANSPORT (See Figs. 7 and 11) TO START ENGINE (See Fig. 7) ADD GASOLINE BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL MOWING TIPS T R A C T 0 R MAINTENANCE SCHEDULE ZERKS GENERAL RECOMMENDATIONS BEFORE EACH USE BRAKE OPERATION TIRES OPERATOR PRESENCE SYSTEM BLADE CARE BLADE REMOVAL (See Fig. 13) CLEAN AIR SCREEN TRANSAXLE COOLING TRANSAXLE PUMP FLUID V-BELTS LUBRICATION CLEANING AIR FILTER ENGINE OIL FILTER TO REMOVE MOWER (See Fig. 18) TO INSTALL MOWER TO LEVEL MOWER HOUSING TO REPLACE MOWER DRIVE BELT TO REPLACE MOWER BLADE (SEC OND ARY) DRIVE BELT (See Fig. 24) TRANSMISSION REMOVAL/RE PLACE MENT TO CHECK AND ADJUST BRAKE (See Fig. 25) TO REPLACE MOTION DRIVE BELT (See Fig. 26) TO START ENGINE WITH A WEAK BAT TERY (See Fig. 28) TO REMOVE WHEEL FOR REPAIRS (See Fig. 27) TO AD JUST STEER ING WHEEL ALIGN- MENT FRONT WHEEL TOE-IN/CAMBER Page STORAGE BATTERY FUEL SYSTEM ENGINE OIL CYLINDER(S) TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION SCHEMATIC NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS A IGNITION SWITCH ELECTRICAL 22 79 21 Page CHASSIS AND ENCLOSURES chassis-stealth.stlt_20 Page Page DRIVE STEERING ASSEMBLY steering_stealth_prem_7 Page ENGINE OPTIONAL EQUIPMENT Spark Arrester Page SEAT ASSEMBLY WHEELS & TIRES DECALS Page MOWER LIFT Page MOWER DECK SECTION 1: LIMITED WARRANTY SECTION 2: HUSQVARNAS OBLIGATIONS UNDER THE WARRANTY SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY SECTION 4: EXCEPTIONS AND LIMITATIONS WARRANTY STATEMENT Charlotte, NC 28269 FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION