Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Z5426, Z4824, Z4219, Z4218 manual Deck belt installation

Models: Z5426 Z4219 Z4218 Z4824

1 80

Download 80 pages 51.79 Kb

Page 45

MAINTENANCE

Deck belt installation

NOTE: For ease in installing the deck belt, refer to the routing decal on bottom of seat.

•Wrap the deck belt around the electric clutch pulley that is located on the engine shaft.

•Route the belt forward between the EZT (E-Series Zeroturn Transaxles) and up onto the deck.

•Place belt around spring loaded idler pulley, between the pulley and guide. Secure bolt and nut.

•Starting on the right hand side of the deck, wrap the belt around the stationary idler pulley, the right mandrel housing, then around to the left mandrel housing.

•Push inward on the idler arm and carefully route belt over stationary idler pulley. Once belt is properly routed, slowly release idler arm to tension belt.

•Double check belt routing to make sure it matches the routing decal, and the belt does not have any twist. Correct as needed.

•Replace belt shields on both mandrel housings and secure with fasteners.

1

1. Clutch pulley

Belt routing, deck belt

English-43

Image 45

Husqvarna Z5426, Z4824, Z4219, Z4218 manual Deck belt installation

Contents

Operator´s manual Page OPERATOR’S Manual Rider Series ContentsEnglish-2 Introduction IntroductionManufacturing Number Good ServiceSymbols and Decals Symbols and DecalsXxxx xxxxxx Objects Engine is Running Moving sharp blades under cover Safety Instructions Safety InstructionsGeneral Operation English-8 Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance Risk of sparking Important Information TransportCustomer responsibilities Controls ControlsControl Locations Tracking Motion Control LeversFuses Seat adjustment knobsBy pass linkages Refueling Blade switchIgnition Switch Choke ControlThrottle Control Hour Meter Parking BrakeMachine must be stopped before activating the parking brake Cutting height pedal AccessoriesOperation OperationTraining Starting the Engine Before StartingDepress the control for disengaging the mower deck Press in and turn the ignition key to the start position To remove cables, reverse order To start an engine with a weak batteryRunning Operating on hills Mowing Tips Stopping the Engine Moving by Hand Maintenance MaintenanceMaintenance Schedule = Described in this manual = Not described in this manual To clean battery and terminals BatteryReplacing battery Always use protective glasses when handling the batteryIgnition System Checking the Safety System Checking the Engines Cooling Air Intake Checking and Adjusting Throttle CableBriggs and Stratton engine Replacing the Air FilterReplacing the Fuel Filter Faulty adjustment can cause an accidentChecking Tire Pressures Checking the Parking BrakeDeck belt Checking the V-beltsDeck belt installation EZT belt To replace EZT E-Series Zeroturn Transaxle beltEZT belt removal Check the blades Checking the BladesAdjusting the Mower Deck To level deck Side-to-side adjustmentFront-to-back adjustment To adjust anti-scalp rollers Use protective glasses when cleaning and washing Cleaning and WashingCaster Wheels HardwareLubrication LubricationLubrication Schedule Lubricating in Accordance with the Lubrication Schedule Lubricating the CablesCaster wheels Engine Oil Briggs & Stratton Changing the Engine OilOil drain valve Changing the Oil Filter Checking the oil levelTransmission Trouble Shooting Guide Trouble Shooting GuideProblem Cause Wrong fuel type English-58 Storage ServiceStorage Winter StorageWiring diagram Wiring DiagramsTechnical Data Technical DataTechnical DataZ4218 Z4219 Equipment Z4824 Z5426 English-64 Torque Specifications Conformity Certificates Conformity CertificatesUSA requirements Service Journal Service JournalDelivery Service Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service English-70 English-71 English-72 At Least Once Each Year English-74 English-75 English-76 Page 113926Rir06/05/06