Mini FasTrak 36/42
Slot
Bypass valve rod (Left rod shown)
(Viewed from the rear left underneath side)
Figure
FasTrak 48/54
Bypass valve rod (Left rod shown)
Bypass valve rod shown in towing position
Figure
5.Insert key in ignition switch and rotate full clockwise to engage starting motor. Release key when engine starts.
IMPORTANT: The engine starter should not be operated for periods longer than 30 seconds at a time. An interval of at least two minutes should be allowed between such cranking periods to protect the starter from over- heating and
6.Perform test to make sure safety start interlock system is operating prop- erly. Refer to Safety start interlock system section.
7.As soon as engine begins to run, check to make certain the oil warning light, engine light and alternator warning light (if applicable) are off. If not, stop engine immediately and check for the cause.
8.Allow the engine to idle a few minutes before advancing the throttle and/ or engaging the deck clutch.
9.Before stopping the engine, place the steering control levers in the park brake position, disengage the deck clutch, and throttle back to low idle for a couple of minutes; then rotate ignition key
Stopping the engine
Use the following procedure to shut off the engine after operating the equipment.
1.Place the steering control levers in the park brake position
2.Disengage the deck clutch
3.Throttle back to low idle for a couple of minutes
4.Rotate ignition key
Moving tractor with stalled engine
If it becomes necessary to move the tractor when the engine is inopera- tive, the transaxles are equipped with bypass valves.
FasTrak 36/42 (Mini FasTrak 36/42) - Before moving the unit, pull out on the bypass valve rods and slide them into the slot to lock in position. Both bypass valve rods are located underneath the rear of the tractor at the back of the transaxle. (Fig.
FasTrak 48/54 - Before moving the unit, pull up on the bypass valve rod and slide it in the slot to the disengaged position.
The steering control levers must be placed in the neutral position, to release the park brakes, so that the tractor can be moved. Both bypass valve rods are located at the front corners of the engine on the engine platform. Fig.
Do not tow the machine. Move it by hand or use a winch to load on a trailer for transporting.
When transporting on another vehicle, the tractor must be secured. IMPORTANT: Always make certain the two bypass valves are returned
to their operating position before running the tractor following repairs.
WARNING: Allow engine exhaust manifold to cool before engaging or disengaging the bypass valves. The bypass valve rods are located close to the exhaust system.
Driving the tractor
DANGER: Never make sudden stops or reverse direction, especially when maneuvering on a slope. The steering is designed for sensitive response. Rapid movement of the steer- ing control levers in either direction could result in a reaction of the tractor that can cause serious injury.
After starting engine, engage the control levers and steer as follows:
To go forward, push steering control levers forward an equal distance (Fig.
To go in reverse, pull steering control levers rearward an equal distance (Fig.
To turn left, move the right steering control lever farther forward from neutral than the left steering control lever.(Fig.
To turn right, move the left steering control lever farther forward from neutral than the right steering control lever. (Fig.
“0” degree turn, move one steering control lever forward and the other steering control lever back of neutral. This will allow the drive wheels to
To stop or decrease speed, move steering control levers to neutral. When going forward pull back gently on steering control levers. When going in reverse push forward gently on steering control levers.
For emergency stop, when traveling forward or rearward, place the steering control levers in the park brake position immediately.
DANGER: When moving in the rearward direction push for- ward gently on steering control levers and avoid sudden move- ment. Any sudden movement could cause the front of the mower to come off of the ground resulting in possible loss of control causing serious injury or death.
To make a three point turn to the right, move the left steering control lever farther forward from neutral than the right steering control lever and start the turn. Next, pull back on the steering control levers until they are past neutral and the machine starts to go rearward. Pull right steering control lever farther rearward from neutral than the left steering control lever until the rear of the machine has pivoted around. Then, push the steering control levers forward until they are both past neutral and the machine starts to go
14 | 601156_0308 |
