Ikelite DCR-SR190, DCR-SR300 instruction manual P R E P A R A T Io N, Ikelite Video Case

Power Zoom

Power

IKELITE VIDEO CASE

SUPPLEMENTAL INSTRUCTIONS FOR

#6038.83 SONY DCR-SR190, 200, 290, 300

Thissupplementalsetofinstructionsdescribesadditionalfeaturesspecific toyourhousingmodel.Priortotestingthesysteminthewater,pleasereadthis supplementalongwiththegeneralinstructionmanualtobecomefamiliarwith itsfeaturesandfunctions.

IkeliteVideoCasesareslightlynegative insaltwaterforstability.Thishousinghas beenwaterpressuretestedatthefactory andhasaworkingdepthof60m(200').

HOUSING CONTROLS______________	Mirror
	Port	Pad
• Power On/Off / Mode		Touch
• Start/Stop
• Power Zoom	Bottom Bar	Lid Snap
• Photo
• LCD Screen Control #1	Base
• LCD Screen Control #2
• LCD Screen Control #3	Snap Shot
• LCD Reversing Circuit On/Off	for Reverse
MAIN O-RING #0109_____________	On/Off
	Circuit
O-rings last several years if
properly maintained. Control seals	Start/
should not ne ed to be replaced as	Stop
long as the control shafts are kept
clean and lightly lubricated.

P R E P A R A T IO N
PACKAGED WITH HOUSING__________________________________________________
• External UR/Pro Color Filter
• Internal Lens Shade
• Silicone Lubricant
COLOR FILTER_____________________________________
The installation and usage of the external UR/Pro
color filter is described in the general instruction manual.
LENS SHADE_______________________________________
The internal lens shade helps block light reflection/
refraction caused by the interaction of the external color
filter and the port.	External	Internal
Carefully thread the lens shade on the front of the	Color Filter	Lens Shade

camera lens. The lens threads are very fine; DO NOT cross thread. It should screw on very easily. If it is difficult to turn, you are cross threading.

Completely thread the lens shade into the camera to avo id any potential clearance or sealing problems when the camera is installed and the housing is sealed.

LCD MONITOR / EXTERNAL MIRROR_________________________________________

The camera's LCD monitor can be viewed from the rear of the housing, using the external mirror featured on the side of the housing.

Open the LCD monitor on the camera, rotate 180°,and then press it back against the side of the camera. The external mirror is hinged so that it can be opened to reflect the image from the camera's LCD monitor for viewing from the rear of the housing.

During transportation, please remember to close the mirror by p ressing it against the rubber on the lid snap.

BATTERY AND TAPE__________________________________________________________

Install a fully charged Sony battery on th e camera:

Sony NP-FP50, NP-FP60, NP-FP90

Other brand batteries may not fit inside the housing.

Make sure you have loaded an appropriate digital cassette tape in the camera. OPTIONAL WIDE ANGLE LENS__________________________________________

The housing’s port accepts optional 67mm threaded waterproof Wide-Angle lenses such as the Ikelite #6420 W-20, Epoque DCL-20 and Inon UWL-100 Type 2 and Sea&Sea (58070). These waterproof lenses secure to the outside of the lens port.

Should you elect to use the optional Ikelite #6420 W-20, Epoque, Inon or Sea&Sea lens, carefully thread the waterproof lens on the front of the lens port. The lens threads are very fine; DO NOT cross thread. It should screw on very easily. If it is difficult to turn, you are cross threading.

INTERNAL WIDE-ANGLE LENS OPTION ________________________________________

Special ports are available for use with the Raynox HD-5050 Pro high definition wide-angle lens. optional ports sold separately as do me port #9304 or flat lens port #9304.1.Raynox HD-5050 Pro lens not included. Lens not available for purchase through Ikelite.