Maintenance |
| |
The Ikelite Digital Housing should be given the same care and |
| |
attention as your other photographic equipment. In addition to |
| |
normal maintenance we recommend that the housing be returned | ||
to Ikelite periodically to be checked and pressure tested. |
| |
1. | Do Not leave the camera and housing in direct sunlight for |
|
2. | prolonged periods. Heat may damage the camera. |
|
Do Not ship the camera in the housing. |
| |
3. | Before using the housing, always check the tightness of the set | |
| screw in each control knob. |
|
| Check each control gland penetrating the housing to make sure | |
| they are tight. There is a slight chance that either could vibrate | |
4. | loose during travel. |
|
Keep the back o’ring clean and lightly lubricated. To lubricate |
| |
| remove the o’ring from the back. Put a small amount of lkelite | |
| lubricant on your fingers. Draw the o’ring through your fingers | |
| to apply a light coating of lubricant. Only apply enough |
|
| lubricant to make the o’ring feel slick. Do Not stretch the o’ring. | |
| This light coating of lubricant will help to keep the o’ring from | |
| drying out and will help to show a dark sealing line when the |
|
5. | housing back is properly sealed. |
|
Keep the area where the o’ring fits and the sealing surface of |
| |
6. | the housing clean. |
|
Rinse the housing exterior thoroughly in fresh water after each | ||
| salt water use. Dry with a soft cloth. Dry lens port to eliminate | |
| water spotting. |
|
| After several uses in salt water soak the housing exterior in a |
|
| mild soap solution, rinse and dry before storage. When storing | |
| the housing, remove the back o’ring, lightly lubricate and place | |
| in a plastic bag. Place the plastic bag with o’ring inside the |
|
| housing for safe keeping. |
|
CAUTION |
| |
| Never use spray lubricants as the propellant ingredient can | 14 |
| cause the plastic housing to crack. |
|
Control Maintenance
Ikelite controls are designed to provide years of reliable service with minimal maintenance.
1. Push button controls require no maintenance other than rinsing in fresh water after saltwater use. If a push button control becomes difficult to push or if it sticks when depressed, soak the housing in luke warm fresh water. After a few minutes operate the push button. If this does not correct the problem, return the housing to Ikelite for maintenance.
lubricate shaft
housing
pull out to expose shaft
Control Maintenance Cont.
3. Some of the controls have a short shaft and cannot be pulled out exposing the shaft for lubrication. In the unlikely event one of these controls sticks or becomes difficult to operate you can remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, loosen the set screw in the knob (allen wrench required); remove the knob. If there is salt or dirt
2.Some of the controls have long shafts. These controls can be pulled out, exposing the shaft (see drawing).
To lubricate the control, gently pull on the knob until the stainless steel shaft is exposed. Lightly lubricate the shaft, then move the shaft in and out several times. This will lubricate the x’ring in the Ikelite control gland. This should be done before using the housing after a prolonged storage period, or once a week when the housing is in use.
control | housing |
|
| gland | |
| |||||
shaft |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Flat Tighten set screw down against this area when
replacing the knob. Lubricate end of shaft before reinserting into gland
Loosen set screw (allen wrench required)
15 | 16 |
