Ikelite SLR-DC Housing
i n s t r u c t i o n m a n u a l
#6871.11 for Canon EOS 10D
AF/WB Mode | Illuminator | Mode | |
Drive Mode | |||
Meter/Flash | Lid Snap | Dial | Strobe |
| Mount | ||
Main Dial |
|
| |
AE/FL |
|
|
|
Lock |
|
| Zoom |
|
|
| |
|
|
| Control |
Port Lock |
|
|
|
Shutter
Release
Lid
Snap
FRONT VIEW
Gear Sleeve
Drive Gear
Port
Opening
Aluminum Tray 
Lens
Release
Rubber
Handle
Strobe
Mount
Congratulations on your purchase of an Ikelite Digital Camera Housing. Ikelite has over 40 years of experience in the underwater photographic and lighting market. Our products are designed and built in the USA by Ikelite for both the professional and amateur photographer.
The clear housing permits instant visual inspection of the camera and all sealing surfaces as well as complete monitoring of controls and camera LCD screens.
Ikelite Digital Housings are slightly negative in salt water for stability. This housing has been water pressure tested at the factory. Housing is pressure tested to 200’ (60m).
Zoom
Quick
Release
Button
Lens
Release
[A] Menu
[B] Info
[C] Jump
BACK VIEW
|
| Viewfinder Port |
|
|
|
| AE/FE Lock |
|
| H | I |
|
|
| |
A |
|
|
|
B |
|
| Shutter |
C |
|
| |
| J | Release | |
D |
|
| |
|
| K |
|
E | F | L |
|
G |
| ||
|
|
| |
External Strobe Connector |
| ||
and Waterproof Cap |
| ||
[D] Direction | [G] On/Off | [J] Set | |
[E] Playback |
| [H] Access | [K] Quick Control Dial |
[F] Erase |
| [I] AF Point | [L] eTTL Mode/Compensation |
2
Lid
Snap
Main Dial
Opening the Housing 1. Lid Snaps have a Lock.
To open, push Lid Snap Lock forward and lift as shown.
AE/AF Lock 
Back O’ring
Shutter
Release
Camera
Tray
Optional
GearPort
Sleeve
Port |
O'ring |
Keep pressure on the Lid
Snap so it does not fly open
quickly.
Some lid snaps have a lot of
spring tension once they go over center, have a firm grip on the lid snap. Lid Snaps may be opened one at a time.
Zoom Clamp
Camera
Mounting
Bolt
SIDE VIEW
Lubricants
1. Ikelite provides silicone lubricant with the housing. We recommend that you use only Ikelite lubricant as some other brands may cause the o’ring to swell and not seal properly.
2. Use only enough lubricant to lightly cover control shafts and o’rings. Wipe off any excess lubricant with a clean cloth. Lubricant is not a sealant, it is used to reduce friction. Excessive lubricant can collect sand and dirt which may interfere with proper sealing.
CAUTION
Never use spray lubricants as the propellant ingredient can cause the plastic housing to crack.
3
Springs
Lens Zoom Grip
Rubber Strips
Groove
Springs
Installing the Zoom Clamp
The two halves of the Zoom Clamp are held together by springs. This allows the Zoom Clamp to be stretched to fit over the zoom grip on different diameter lenses. The Zoom Clamp should fit tight around the lenses zoom grip so that it does not slip when using it to rotate the camera’s zoom ring. If the Clamp is loose, adhere the thin black rubber strips to the inside of each half of the Zoom Clamp as shown above. The Zoom Clamp has two extended ears with grooves. These grooves accept the Ribs on Gear Sleeve.
4
