Ikelite iTTL Adapter

i nstruc

tio n ma

nual

#4301 for Specified Nikon & Fuji Digital SLR Cameras

in Non-Ikelite Housings

Ikelite iTTL Adapter

instru

ction

man ual

#4301 for Specified Nikon & Fuji Digital SLR Cameras

in Non-Ikelite Housings

Delrin Pod

Knurled Ring (Rotate)

Ikelite

Bulkhead

O-ring

Ikelite iTTL Adapter

Delrin Pod

Knurled Ring (Rotate)

Ikelite

Bulkhead

O-ring

Ikelite iTTL Adapter

Ikelite Connector

Ikelite Waterproof Cap

The Ikelite iTTL Adapter is for use with Non-Ikelite housings with a TTL hot-shoe & Ikelite-style bulkhead.

(hot-shoe must have all 5 wires connected)

Refer to housing specifications or contact housing manufacturer for

connector style and wiring information.

The Adapter offers both TTL and Manual operation. Exposure compensation is not provided through the Adapter,

but can be accessed via the camera’s menus.

The Ikelite iTTL Adapter is compatible with the following Digital Cameras; Nikon D-40, D-50, D-70, D-70s,

D80, D-200 and Fuji S5 Pro.

The Ikelite iTTL Adapter is Not compatible with the following Nikon Cameras; D-100,D-1X,D-2X, D-2H.

Connecting Adapter to houing________________________

• Make sure all components are dry.

• Clean and lightly lubricate the o-ring on the male Ikelite connector. Check o-ring for cracks or nicks.

• Lightly lubricate the threads on the housing bulkhead.

• Note the positioning of the receptacles and pins. Properly align the end of the sync cord and insert it into the housing bulkhead.

• Hand tighten the knurled ring on the sync cord until there is no in-out movement between sync cord connector and housing bulkhead. Connecting DS Substrobes __________________________

Use ONLY with Ikelite DS Substrobes. DS50/51, DS125, DS200 (see strobe compatibility chart on reverse side)

• Make sure all components are dry.

• Remove the waterproof cap from the Ikelite bulkhead on the black delrin pod.

• Clean and lightly lubricate the o-ring on the male Ikelite connector. Check o-ring for cracks or nicks.

• Lightly lubricate the threads on the adapter bulkhead.

• Note the positioning of the receptacles and pins. Properly align the end of the sync cord connector and insert it into the adapter’s bulkhead.

Hold the adapter’s knurled ring when tightening the sync cord.

• Hand tighten the knurled ring on the sync cord until there is no in-out movement between sync cord connector and adapter bulkhead.

Single or DualIkelite sync cords can be attached.

Dual strobe use requires dual sync cord.

Two strobes cannot be operated by independent adapters.

Ikelite Connector

Ikelite Waterproof Cap

The Ikelite iTTL Adapter is for use with Non-Ikelite housings with a TTL hot-shoe & Ikelite-style bulkhead.

(hot-shoe must have all 5 wires connected)

Refer to housing specifications or contact housing manufacturer for

connector style and wiring information.

The Adapter offers both TTL and Manual operation. Exposure compensation is not provided through the Adapter,

but can be accessed via the camera’s menus.

The Ikelite iTTL Adapter is compatible with the following Digital Cameras; Nikon D-40, D-50, D-70, D-70s,

D80, D-200 and Fuji S5 Pro.

The Ikelite iTTL Adapter is Not compatible with the following Nikon Cameras; D-100, D-1X, D-2X, D-2H.

Connecting Adapter to houing________________________

• Make sure all components are dry.

• Clean and lightly lubricate the o-ring on the male Ikelite connector. Check o-ring for cracks or nicks.

• Lightly lubricate the threads on the housing bulkhead.

• Note the positioning of the receptacles and pins. Properly align the end of the sync cord and insert it into the housing bulkhead.

• Hand tighten the knurled ring on the sync cord until there is no in-out movement between sync cord connector and housing bulkhead. Connecting DS Substrobes __________________________

Use ONLY with Ikelite DS Substrobes. DS50/51, DS125, DS200 (see strobe compatibility chart on reverse side )

• Make sure all components are dry.

• Remove the waterproof cap from the Ikelite bulkhead on the black delrin pod.

• Clean and lightly lubricate the o-ring on the male Ikelite connector. Check o-ring for cracks or nicks.

• Lightly lubricate the threads on the adapter bulkhead.

• Note the positioning of the receptacles and pins. Properly align the end of the sync cord connector and insert it into the adapter’s bulkhead.

Hold the adapter’s knurled ring when tightening the sync cord.

• Hand tighten the knurled ring on the sync cord until there is no in-out movement between sync cord connector and adapter bulkhead.

Single or Dual Ikelite sync cords can be attached.

Dual strobe use requires dual sync cord.

Two strobes cannot be operated by independent adapters.

Instructions continued on reverse side

Instructions continued on reverse side

Page 1
Image 1
Ikelite instruction manual Ikelite iTTL Adapter, Nstruc Tio n ma Nual, Instru Ction Man ual