Installation

Positioning the Appliance

Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level. In any case, the appliance should not be inclined more than 2°.

If the appliance is level, it will help ensure proper perfor- mance.

This dishwasher model can be built-in under the one worktop, and it therefore comes provided with an instructions sheet.

Cold Water Connection

Connect the cold water supply hose to a threaded 3/4 (gas) connector, inserting the small filter supplied with the dishwasher and making sure

that it is fastened tightly in place (see figure 2).

If the water pipes are new or have not been used for an extended period of time, let the

water run to make sure that the

A

 

water is clear and free of

 

impurities. If this precaution is

 

not taken, there is a risk that the

Fig.2

water inlet can get blocked and

 

damage the appliance.

 

Hot Water Connection

The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60° C.

In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line.

Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4 cm., or let it run into the sink, making sure to avoid bending or crimping it. Use the speical plastic support that comes with the appliance (see figure to the right). The free end of the hose must be at a height between 40 and 100 cm.and must not be immersed in water.

Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is sized for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than using adpators or the like as they could cause overheating and burns.

Should the electricity supply cable be damaged, we recommend that you only contact authorised Technical Service Centres for the replacement.

GB

10

Page 11 Page 13
Page 12
Image 12
Indesit D41 manual Installation
Page 11 Page 13

D41 specifications

The Indesit D41 is a highly regarded tumble dryer designed to deliver exceptional performance and convenience for modern households. As a front-loading dryer, it offers ease of access, making it user-friendly for everyone. With a sleek, white exterior, its design embodies a blend of functionality and style, easily integrating into any laundry room or space.

One of the standout features of the Indesit D41 is its capacity. With a sizable drum that can accommodate up to 7 kg of laundry, it is perfect for families and those with larger loads. This capacity ensures that users can dry more clothes in a single cycle, saving both time and energy.

The Indesit D41 comes equipped with multiple drying programs tailored to various fabric types and laundry needs. From cotton to synthetics, users can select the appropriate cycle for optimal results. The sensor drying technology is a significant highlight, as it automatically adjusts drying time based on the moisture levels detected in the load. This feature not only prevents over-drying, which can damage clothes, but it also helps to conserve energy—making it an environmentally friendly option.

Another important characteristic of the Indesit D41 is its simplicity of use. With an intuitive control panel, users can easily navigate through the different settings and programs. The timer function adds to the convenience, allowing users to schedule their laundry around their busy lives.

In terms of energy efficiency, the D41 achieves a good rating, providing cost savings on electricity bills without compromising on performance. Moreover, the machine operates with relatively low noise levels, ensuring minimal disturbance during operation.

Maintaining the Indesit D41 is straightforward, thanks to its easy-to-clean filter. Regular maintenance extends the lifespan of the appliance and ensures it operates at peak efficiency.

In summary, the Indesit D41 combines capacity, innovative drying technologies, user-friendly controls, and energy efficiency. Its blend of functionality and style makes it an excellent choice for those seeking a reliable and effective tumble dryer that meets the demands of everyday life. Whether for a busy family or a single user, the Indesit D41 stands out as a practical solution for laundry needs.
Top Page Image Contents