Troubleshooting
195075388.01
02/2009 - Xerox Fabriano
Whenever the appliance fails to work, check for a solution from the following list before calling for EN Assistance.
| Malfunction: | Possible causes / Solutions: |
| |
| The dishwasher does not start. | • The plug has not been inserted into the electrical socket properly, or |
| |
|
| there is no power in the house. |
| |
|
|
|
| |
|
| • The dishwasher door has not been shut properly. |
| |
|
| • | A delayed start has been programmed ( see Start- up and use ) . |
|
|
| • The dishwasher cycle has not yet finished. |
| |
| No water drains out from the | • | The water outlet hose is bent ( see Installation). |
|
| dishwasher. | • | The drain duct is blocked. |
|
|
| • The filter is clogged up with food residues . |
| |
| The dishwasher makes | • | The dishes are rattling against each other or against the sprayer |
|
| excessive noise. |
| arms . |
|
|
| • | An excessive amount of foam has been produced: the detergent has |
|
|
|
| not been measured out correctly or it is not suitable for use in |
|
|
|
| dishwashers (see Start - up and use). |
|
| The dishes and glasses are | • | The level of the refined salt is low or the dosage setting is not |
|
| covered in a white film or |
| suited to the hardness of the water ( see Rinse aid and salt). |
|
| limescale deposits. | • The lid on the salt dispenser is not closed properly. |
| |
|
|
| ||
|
| • The rinse aid has been used up or the dosage is too l ow. |
| |
|
| • The crockery is made from non- stick material. |
| |
| The dishes and glasses are |
|
|
|
| streaked or have a bluish | • | The rinse aid dosage is too high. |
|
| tinge. |
|
|
|
| The crockery has not been dried | • | The rinse aid has been used up or the dosage is too low ( see Rinse |
|
| properly. |
| aid and salt). |
|
|
| • The rinse aid dispenser setting is not high enough. |
| |
|
| • | A wash cycle without a drying programme has been selected. |
|
| The dishes are not clean. | • | The racks are overloaded ( see Loading the racks ). |
|
|
| • The crockery has not been arranged well . |
| |
|
| • The sprayer arms cannot move freely. |
| |
|
| • The wash cycle is too gentle (see Wash cycles ). |
| |
|
| • | An excessive amount of foam has been produced: the detergent has |
|
|
|
| not been measured out correctly or it is not suitable for use in |
|
|
|
| dishwashers (see Start - up and use). |
|
|
| • The lid on the rinse aid compartment has not been shut correctly. |
| |
|
| • The filter is dirty or blocked ( see Care and maintenance). |
| |
|
| • The refined salt level is low ( see Rinse aid and salt). |
| |
| No water enters the | • | There is no water in the mains supply. |
|
| dishwasher/Shut off tap alarm. | • | The water inlet hose is bent ( see Installation). |
|
| (several short beeps are emitted) | • | Turn on the tap and the appliance will start after a few minutes. |
|
| (the 2 (Normal) and 3 (Soak) WASH | • | The appliance lock has been activated because no action was taken |
|
| CYCLES indicator lights flash). |
| when the beeps sounded. Switch off the machine, using the ON/OFF |
|
|
|
|
| |
|
|
| button, turn on the tap and switch the machine back on after 20 |
|
|
|
| seconds by pressing the same button. Re- programme the machine |
|
|
|
| and restart the wash cycle. |
|
| Water loading solenoid valve | • | Switch off the machine by pressing the ON/OFF button and switch it |
|
| malfunction alarm |
| back on after a minute. If the alarm continues, turn off the water tap |
|
| (the 2 (Normal) WASH CYCLE |
| to reduce the risk of flooding, remove the plug from the electrical |
|
| indicator lights flash). |
| socket and call Assistance. |
|
|
|
|
| |
| Water inlet hose alarm/Water inlet | • | Switch off the appliance by pressing the ON/OFF button. Shut off |
|
| filter blocked. |
| the water tap to eliminate the risk of flooding and remove the plug |
|
| (the 1 (Intensive), the 2 (Normal) and |
| from the electrical socket. |
|
| the 3 (Soak) WASH CYCLES |
| Make sure the wat er inlet filter has not become blocked by various |
|
| indicator lights flash). |
| impurities . (see “Care and maintenance” chapter) . |
|
|
|
|
|
|
12