Indesit PWDE8148W instruction manual How to run a wash cycle or a drying cycle, Close the Door

How to run a wash cycle or a drying cycle

GB	1. SWITCH THE MACHINE ON. Press the
	button; the START/PAUSE indicator light will flash
	slowly in a blue colour.
	2. LOAD THE LAUNDRY. Open the porthole door.
	Load the laundry, making sure you do not exceed
	the maximum load value indicated in the table of
	programmes and wash cycles on the following page.
	3. MEASURE OUT THE DETERGENT. Pull out the
	detergent dispenser drawer and pour the detergent
	into the relevant compartments as described in
	“Detergents and laundry”.
	4. CLOSE THE DOOR.
	5. SELECT THE WASH CYCLE. Use the WASH
	CYCLE SELECTOR knob to select the desired wash
	cycle. A temperature and spin speed is set for each
	wash cycle; these values may be adjusted. The
	duration of the cycle will appear on the display.
	6. CUSTOMISE THE WASH CYCLE. Use the
	relevant buttons:
	Modify the temperature and/or spin
	speed. The machine automatically displays the
	maximum temperature and spin speed values set for
	the selected cycle, or the most recently-used settings
	if they are compatible with the selected cycle. The
	temperature can be decreased by pressing the
	button, until the cold wash “OFF” setting is reached.
	The spin speed may be progressively reduced by
	pressing the	button, until it is completely excluded
	(the “OFF” setting). If these buttons are pressed
	again, the maximum values are restored.
	Setting the drying cycle
	The first time the button		is pressed, the machine

will automatically select the maximum drying cycle which is compatible with the selected wash cycle. Subsequent presses will decrease the drying level and then the drying time, until the cycle is excluded completely ("OFF"). If these buttons are pressed again, the maximum values are restored.

Drying may be set as follows:

A- Based on the desired laundry dryness level: Iron: suitable for clothes which will need ironing afterwards. the remaining dampness softens creases, making them easier to remove. "A1" appears on the display.

Hanger: ideal for clothes which do not need to be dried fully. "A2" appears on the display. Cupboard: suitable for laundry which can be put back in a cupboard without being ironed. "A3" appears on the display.

Extra: suitable for garments which need to be dried completely, such as sponges and bathrobes. "A4" appears on the display.

B - Based on a set time period: between 30 and 180 minutes (Max. load 4 kg).

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table of programmes), perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this procedure for the remainder of the load.

Acooling-down period is always added to the end of each drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle (11-12-13) in accordance with the type of fabric. The desired drying level or time may also be set using the DRYING button .

Modify the cycle settings.

•Press the button to enable the option; the indicator light corresponding to the button will switch on.

•Press the button again to disable the option; the indicator light will switch off.

￿If the selected option is not compatible with the set wash cycle, the indicator light will flash and the option will not be activated.

￿If the selected option is not compatible with a previously selected one, the indicator light corresponding to the first function selected will flash and only the second option will be activated; the indicator light for the option which has been activated will be illuminated.

Note: if the SMART option has been selected, none of the incompatible options may be activated.

￿The options may affect the recommended load value and/or the duration of the cycle.

7.START THE WASH CYCLE. Press the START/ PAUSE button. The corresponding indicator light will

turn blue, remaining lit in a fixed manner, and the door will be locked (the DOOR LOCKED symbol will be lit). To change a wash cycle while it is in progress, pause the washer-dryer using the START/PAUSE button (the START/PAUSE indicator light will flash slowly in an amber colour); then select the desired cycle and press the START/ PAUSE button again. To open the door while a

cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched off the door may be opened. Press the START/ PAUSE button again to restart the wash cycle from the point at which it was interrupted.

8.THE END OF THE WASH CYCLE. This will be

indicated by the text “END” on the display; when the DOOR LOCKED symbol switches off the door may be opened. Open the door, unload the laundry and switch off the machine.

￿If you wish to cancel a cycle which has already begun, press and hold the button. The cycle will be stopped and the machine will switch off.

8