
C255ES Infinity Classia™
Infinity® Loudspeaker Troubleshooting/Repair Tips
Most customers prefer to do simple loudspeaker repairs themselves. By following the steps below, a majority of loudspeakers can be returned to their original factory performance level with minimum effort. Choose the example that best describes the problem you are experiencing.
Problem 1: No sound or distorted sound from one loudspeaker in a pair (or set)
Connect the dead/distorting loudspeaker to a different amplifier channel (one that had a functioning loudspeaker connected to it). If it functions normally, the problem is not
Refer to the wiring diagram and exploded view below. The network is a small circuit board found on the inside of the terminal cup, or mounted to an inside wall of the enclosure. It sends
Problem 2: No sound or distorted sound from one or more (but not all) drivers in an enclosure
Remove the problem driver(s) from the enclosure and make sure all wires are secure and connected. If they are, proceed with the following test: Woofer or midrange driver – Connect the driver’s + and – input terminals directly to the loudspeaker wires from your receiver/amplifier and play some music at a reasonable volume. If the driver now sounds normal (produces a clean, undistorted sound), the network is most likely defective. Tweeter – Replace the tweeter with a functioning tweeter from another loudspeaker. If the tweeter now functions normally (produces clean, undistorted sound), the original tweeter is defective. If the replacement tweeter also sounds distorted or produces no sound, the network is most likely defective.
Problem 3: Loudspeakers distort, rattle or pop at higher volumes
This is usually NOT a loudspeaker problem. Common causes are too much power (playing the loudspeakers too loud and causing them to distort), an amplifier with not enough power (the amplifier can’t produce the required volume without distorting), excessive equalization (turning the tone controls too far clockwise, and/or engaging the loudness/bass boost button on your receiver) or some combination of the above. If only one loudspeaker is exhibiting the problem, and you’re confident that it’s not caused by too little power/too much power/excessive equalization, see solutions for Problems 1 and 2.
WIRING DIAGRAM | ||
Blue + | ||
TRANSDUCER | ||
| ||
130W33801 | Black – | |
| ||
White + | ||
TRANSDUCER |
| |
025D38501 | Black – | |
CROSSOVER | ||
| NETWORK | |
Yellow + | ||
TRANSDUCER | ||
| ||
025D38501 | Black – | |
| ||
Green + | ||
TRANSDUCER | ||
| ||
130W33801 | Black – | |
|
EXPLODED VIEW | 31 | ||
|
|
| |
| 30 |
| 32 |
|
|
| |
| 14 |
| 27 |
|
|
| 15 |
|
|
| 1 |
|
|
| 2 |
|
|
| 3 |
29 | 28 |
| 4 |
12 |
|
| |
|
| 5 | |
| 13 | 10 | |
| 11 |
| |
|
| 9 |
|
|
| 8 |
|
|
| 7 | 6 |
ITEM | PART NO. | DESCRIPTION | QTY. |
1 | Not for Sale | Label | 1 |
2 | Crossover network w/ | 1 | |
|
| terminal cup, binding posts |
|
3 | 4 | ||
4 | 130W33801 | 2 | |
5 | Trim ring, woofer | 2 | |
6 | Front grille | 2 | |
7 | Base, wedge | 1 | |
8 | Faceplate, tweeter | 2 | |
9 | Grille cup | 8 | |
10 | Not for Sale | C255ES cabinet | 1 |
11 | Not for Sale | Label | 1 |
12 | Infinity logo | 2 | |
13 | Switch plate | 1 | |
14 | 025D38501 | 1" Tweeter | 2 |
15 | Not for Sale | Label | 1 |
16 | Not for Sale | Plastic bag | 1 |
17 | Visit www.infinitysystems.com | Owner’s manual | 1 |
18 | Not for Sale | Plastic bag | 1 |
19 | Base, wedge | 1 | |
20 | Top & bottom foam (set) | 1 | |
21 | Not for Sale | Plastic bag | 1 |
22 | Not for Sale | Cloth bag | 1 |
23 | C255ESBK or C255ESCH | C255ES | 1 |
24 | C255ESBK outer carton | 1 | |
| C255ESCH outer carton | 1 | |
25 | Warranty card | 1 | |
26 | Not for Sale | Label | 1 |
27 | Shorting straps | 1 | |
|
| (right/left pair) |
|
28 | Screw, switch, faceplate | 4 |
SERVICE NOTES
A Phillips screwdriver and 3mm Allen wrench (hex key) are required to service this product.
29 | Screw, woofer, | 16 | |
|
| tweeter, trim ring |
|
30 | Screw, tweeter | 2 | |
31 | Screw, wall bracket | 8 | |
32 | Screw, terminal cup | 4 |