CONNECTIONS
If your receiver/processor does not have subwoofer outputs for the left and right channels or an LFE output:
If your receiver/processor has subwoofer outputs for the left and right channels:
RECEIVER/PROCESSOR
RECEIVER/AMPLIFIER
Front Speaker Output
Line Level | Input |
| Bass | ||||
In | Out | Select | 80Hz |
| Filter | Phase | Optimization |
L |
| L |
|
|
|
| System |
|
| Speaker |
|
| On | 180o | On |
R |
| R |
|
|
| 0o |
|
|
| Line | 50Hz | 150Hz | Off | Off | |
+ | – | – | + |
|
|
|
|
Right |
|
|
|
|
|
|
|
Left |
|
|
|
|
|
| Freq. |
|
|
|
|
|
|
| |
+ In | – | – Out | + |
|
|
| Level |
SPEAKER | LEVEL |
|
|
|
| ||
|
|
|
|
| |||
|
|
|
|
|
|
| Width |
Caution: For continued protection against risk of fire, |
|
|
| ||||
| replace only with same type fuse and rating. |
|
|
| |||
| Attention: Utiliser un fusible de rechange |
|
|
|
| ||
Line Level | Input |
| Bass | ||||
In | Out | Select | 80Hz |
| Filter | Phase | Optimization |
L |
| L |
|
|
|
| System |
|
| Speaker |
|
| On | 180o | On |
R |
| R | 50Hz | 150Hz |
| 0o |
|
|
| Line | Off | Off | |||
+ | – | – | + |
|
Right |
|
|
|
|
Left |
|
|
| Freq. |
|
|
|
| |
+ In | – | – Out | + |
|
| SPEAKER LEVEL |
| Level | |
|
|
| ||
|
|
|
| Width |
Caution: For continued protection against risk of fire, | ||||
| replace only with same type fuse and rating. | |||
| Attention: Utiliser un fusible de rechange | |||
| de meme type et calibre. | |||
3A 120VAC 60Hz | 3A 250V | POWER | ||
|
|
|
| On |
Off
LR106476
WARNING: SHOCK HAZARD • DO NOT OPEN
NO USER SERVICEABLE PARTS INSIDE
AVIS: RISQUE DE CHOC ELECTRONIQUE
NE PAS OUVRIR
•Set Input Selector to “Line.”
•Set
de meme type et calibre. | ||
3A 120VAC 60Hz | 3A 250V | POWER |
|
| On |
Off
LR106476
WARNING: SHOCK HAZARD • DO NOT OPEN
NO USER SERVICEABLE PARTS INSIDE
AVIS: RISQUE DE CHOC ELECTRONIQUE
NE PAS OUVRIR
NOTE: Some receivers have a single subwoofer output (do not confuse this with a single LFE output as described below).
In that case, it is recommended that you use a Y connector (not included) to maximize performance.
If you have a Dolby* Digital or DTS® receiver/ processor with a
•Set Input Selector to “Speaker.”
•Set
RED = +
BLACK = –
1.LOOSEN TERMINALS
2.INSERT BARE END; TIGHTEN TERMINALS
NO STRIPE = – |
| STRIPE = + |
|
|
|
|
|
|
SUBWOOFER OR
LFE OUTPUT
Line Level | Input |
| Bass | ||||
In | Out | Select | 80Hz |
| Filter | Phase | Optimization |
L |
| L |
|
|
|
| System |
|
|
|
| 180° |
| ||
|
| Speaker |
|
| On | On | |
R |
| R |
|
|
| 0° |
|
|
| Line | 50Hz | 150Hz | Off | Off | |
+ | – | – | + |
|
Right |
|
|
|
|
Left |
|
|
| Freq. |
|
|
|
| |
+ In | – | – Out | + |
|
| SPEAKER LEVEL |
| Level | |
|
|
| ||
|
|
|
| Width |
Caution: For continued protection against risk of fire, | ||||
| replace only with same type fuse and rating. | |||
| Attention: Utiliser un fusible de rechange | |||
| de meme type et calibre. | |||
3A 120VAC 60Hz | 3A 250V | POWER | ||
|
|
|
| On |
Off
LR106476
WARNING: SHOCK HAZARD • DO NOT OPEN
NO USER SERVICEABLE PARTS INSIDE
AVIS: RISQUE DE CHOC ELECTRONIQUE
NE PAS OUVRIR
•Set Input Selector to “Line.”
•Set
NOTE: In this case, you do not need to use a Y connector. Simply connect the LFE output on your receiver/processor to either the left or right input on the subwoofer.
INTERLUDE IL100S, IL120S | 3 |
