Infinity TSS-750 Operation, Maintenance And Service, Surround Modes, Final Positioning, Power On

OPERATION

Surround Modes

When using the TSS-750 in a Dolby Pro Logic* home theater system, make sure the receiver’s center channel mode is set to “Normal.” When using the system in a Dolby Digital or DTS home theater system, make sure all speakers are set to “Small”.

Some Dolby Digital-equipped receivers/processors offer different setup options for each source or surround mode, e.g., CD-stereo, videotape, Dolby, Pro Logic. In each case, follow your equipment’s instructions to ensure that the subwoofer output is turned on and that the speakers are set to “Small” in each mode.

Power On

Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on the back of the receiver.

Initially set the Subwoofer Level Control	to the“MIN” position.
Turn on the subwoofer by pressing the Power Switch		on the
rear panel.

Turn on your entire audio system and start a CD or movie sound- track at a moderate level.

Auto On/Stand-By

With the Power Switch in the ON position, the LED on the front panel will remain lit in red or green to indicate the On/Stand-By mode of the subwoofer.

RED = STAND-BY (No signal detected, Amp Off)

GREEN = ON (Signal detected, Amp On)

The subwoofer will automatically enter the Stand-By mode after approximately 10 minutes when no signal is detected from your system. The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch

can be left on. You may turn off the Power Switch	for extended
periods of nonoperation, e.g., when you are away on vacation.

Adjust Level

Turn the Subwoofer Level Control up about half way. If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cables making proper contact? Is the AC plug connected to a “live” receptacle? Has the Power Switch been pressed to the “On” position? Once you have confirmed that the subwoofer is active, proceed by playing a CD or DVD. Use a selection that has ample bass information.

Set the overall volume control of the receiver/processor to a

comfortable level. Adjust the Subwoofer Level Control	until
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many

users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must

be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but never obtrusive.

Crossover Adjustment

The Crossover Frequency Control determines the highest frequency at which the subwoofer reproduces sounds. For the TSS-750, it is recommended that this control be set at 120Hz (approximately the 3 o’clock position).

NOTE: This control will have no effect if the LFE/Normal Switch is set to LFE. If you have a Dolby Digital or DTS receiver/

processor, the Low-Pass Frequency is set by the receiver/ processor. Set the LFE/Normal Switch on the subwoofer to LFE. Consult your owner’s manual to learn how to view or change this setting. A setting of 120Hz – 150Hz is recommended.

Phase Control

The Phase Switch determines whether the subwoofer speaker’s piston-like action moves in and out with the main speakers, 0˚, or opposite the main speakers, 180˚. Proper phase adjustment depends on several variables such as room size, subwoofer placement and listener position. Adjust the phase switch to maximize bass output at the listening position.

Final Positioning

After correctly connecting the TSS-750 system and verifying that both the subwoofer and all satellite speakers are playing, it is time to optimize the system for your particular listening room. Earlier, you placed the subwoofer in its general location. Finding the exact location for optimum performance sometimes only involves moving the speakers up to a few inches in any direction. We urge you, therefore, to experiment with placement, if possible, until your speakers deliver their full potential.

MAINTENANCE AND SERVICE

The satellite and subwoofer enclosures may be cleaned using a soft cloth to remove fingerprints or to wipe off dust.

All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions, and other factors, but once per year is the minimum.

If a problem occurs, make sure that all connections are properly made and clean. If a problem exists in one loudspeaker, reverse the connection wires to the left and right system. If the problem remains in the same speaker, then the fault is with the loud- speaker. If the problem appears in the opposite speaker, the cause is in another component or cable. In the event that your TSS-750 ever needs service, contact your local Infinity dealer or Infinity directly at 1-800-553-3332 (USA only) or www.infinitysystems.com for a service center near you.

TSS-750 6