![](/images/new-backgrounds/1255732/2557321x1.webp)
OPERATOR’S MANUAL |
| ||
|
|
| |
INCLUDING:SERVICE KITS, GENERAL DESCRIPTION & TROUBLESHOOTING | RELEASED: | ||
ALSO INCLUDE MANUALS: | IPP/PSE | ||
|
| ||
FORMATION SHEET. |
|
|
|
3” AIR MOTOR |
|
|
|
5:1 RATIO | PUMP |
|
|
2 1/4” STROKE |
|
| |
|
|
|
|
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
SERVICE KITS
• Use only genuine AROR replacement parts to assure compatible |
pressure rating and longest service life. |
Air Inlet 2608 Connector
• |
GENERAL DESCRIPTION
This model is designed for high volume delivery of low viscosity fluids such as motor oil, gear oil or transmission fluids. Material dispensing accessories and supply lines and fittings must be capable of withstand$ ing pressures developed by pump.
• The ARO 5:1 ratio basic pump assembly consists of a 3" air motor |
25 5/16
66419 Air Motor
1/2 NPT Mat’l Outlet
Lower Pump
and ball check lower pump end. |
• The ball check design provides for easy priming of the lower foot |
valve. Material is delivered to the pump discharge outlet on both |
the up and down stroke. |
RATIO x REGULATED AIR PRESSURE TO AIR MOTOR = MAXIMUM FLUID PRESSURE.
•The 5:1 ratio is an expression of the relationship between the air motor area and the lower pump end area. When 150 p.s.i. (10 bar) air pressure is supplied to the air motor, the lower pump end will develop a maximum of 786 p.s.i. (54 bar) fluid pressure (at no flow) - as the fluid control is opened, the flow rate will increase as the air motor cycle rate increases to keep up with the demand.
(643 mm)
15 11/16” | FIGURE 1 |
(398.4 mm) |
|
1 1/2 NPT Mat’l Inlet
| INCLUDED BUT NOT |
F022 | SHOWN: 210 COUPLER |
OPERATING AND SAFETY PRECAUTIONS
|
|
|
|
|
|
|
• | HEED ALL WARNINGS. | • Do not operate pump continuously at speeds in excess of 75 cycles per min$ | ||||
• | DO NOT EXCEED MAXIMUM WORKING PRESSURE OF 786 PSI (54 | • | ute. | |||
| BAR) AT 150 PSI (10 BAR) AIR INLET PRESSURE. | Disconnect air line from pump air motor when system sits idle for long peri$ | ||||
|
|
|
| ods of time. | ||
| WARNING | : HIGH PRESSURE DEVICE. Improper usage of |
| |||
| • Materialsand solvents being pumped by this pump must be compatible with | |||||
| this equipment could result in serious injury. The possibility | |||||
|
| the parts of this pump that come in contact with the material and solvent. | ||||
| of injection into the flesh is a potential hazard. Never allow any |
| ||||
|
|
|
|
| ||
| part of the human body to come in front of or in direct contact |
| WARNING | : PREVENT STATIC SPARKING. If static sparking | ||
|
| occurs, fire or explosion could result. Pump, dispensing | ||||
| with the material outlet. An injection injury can be serious. If |
| ||||
| injection should occur, contact a qualified physician immedi! |
| valve and containers must be grounded when handling in! | |||
• | ately for treatment. |
| flammable fluids such as petroleum products, paints, lac! | |||
COMPONENTRUPTURE. This pump iscapableofproducinghighmaterial |
| quers, etc. and wherever discharge of static electricity is a | ||||
• | pressure as stated on pump model plate. | • | hazard. | |||
Be sure material hoses and other components are able to withstand fluid | Use grounded hoses (static wire) and be sure the object is grounded if it can | |||||
| pressures developed by this pump. |
| produce a static charge. |
THE ARO CORPORATION D ONE ARO CENTER D BRYAN, OHIO
&(419)
E1995 THE ARO CORPORATION D PRINTED IN U.S.A.