60702 2’’ AIR MOTOR PARTS LIST
1
2
3Figure 5
5
6
8
9
10 7
11
12
13
14
15
16
17
18
19
20
21
22
93005 Ground Screw
Item | Description (size) | Qty | Part No. | |
n | Service Kit Parts |
| 66098 | |
1 | Cap | 1 | ||
n 2 | “O” Ring (3/32” x | 1 | ||
3 | Spring | 1 | 77208 | |
4 | Button | 1 | 90638 | |
5 | Washer | 1 | 77290 | |
6 | Cylinder | 1 | ||
n 7 | Spacer & Piston Assembly | 1 | 61088 | |
8 | Screw (#4 - 40 x 3/8”) | 3 | ||
9 | Valve Plate | 1 | 76090 | |
10 | Piston Assembly | 1 | 60656 | |
11 | Valve Spacer | 1 | 76856 | |
n 12 | Gasket | 1 | ||
13 | Plunger Tip | 1 | 76208 | |
14 | “O” Ring (1/8” x | 1 | ||
15 | Plunger | 1 | 76215 | |
n 16 | “O” Ring (3/32” x | 1 | ||
17 | Valve Spring | 1 | 76070 | |
18 | Pump Body | 1 | ||
n 19 | “O” Ring (0.275” x 1.837” o.d.) | 1 | 77803 | |
20 | Washer | 1 | 76075 | |
21 | Lock Ring | 1 | 76100 | |
22 | Separating Tube | 1 | 76216 |
2” AIR MOTOR REASSEMBLY
Refer to Figure 5.
1.Insert the (11) valve spacer through the bottom of the (10) piston as- sembly.
2.Place the (9) valve plate on top of the (10) piston assembly (side with three protrusions) to face (10) piston assembly and align the three holes with the three posts of the (11) valve spacer.
3.Fasten the (9) valve plate down with the three (8) screws (this is the
(7)spacer and piston assembly). Lay aside.
4.Thoroughly grease the (19) “O” ring and place into the (18) pump body.
5.Place the (20) washer in the (18) pump body.
6.Screw the (22) separating tube securely to the (18) pump body.
7.Tighten the (21) lock ring.
8.Grease the (16) “O” ring and place over the threads of the (18) pump body.
9.Place the (17) valve spring into the (18) pump body.
10.Place the (15) plunger with (13) plunger tip through the (22) separat- ing tube and through the (18) pump body. NOTE: To prevent dam- age to (19) “O” ring apply light film of grease on (15 and 13) assembly.
11.Place the (12) gasket over the threads of (13) plunger tip.
12.Screw the (7) spacer and piston assembly onto the (13) plunger tip and tighten with wrenches, using flats provided.
13.Thoroughly grease the inside of the (6) cylinder and insert it over the
(7)spacer and piston assembly.
14.Thread the (6) cylinder on the (18) pump body.
15.Screw the (1) cap, with (2) “O” ring, (3) spring, (4) button and (5) washer, in place on the (6) cylinder and tighten with a strap wrench.
Page 4 of 8 |