Ingersoll-Rand AD40A-X-X manual 1 1 RATIO METALLIC, Read This Manual Carefully Before Installing

OPERATOR’S MANUAL AD40A-X-X

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1-1/2” DIAPHRAGM PUMP

1:1 RATIO (METALLIC)

RELEASED: 4-22-05

REVISED: 12-2-10 (REV. 05)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to “Model Description Chart” to match the pump material options. 637436 for air section repair (see page 6).

637426-XX for fluid section repair (see page 4).

PUMP DATA

Models	see “Model Description Chart” for “-XXX”
Pump Type	Metallic Air Operated Double Diaphragm
Material	see “Model Description Chart”

Weight . . .	AD40A-XAX-XXX	50.9 lbs (23.1 kg)
	AD40A-XCX-XXX	78.9 lbs (35.8 kg)
	AD40A-XSX-XXX	83.9 lbs (38.0 kg)
Maximum Air Inlet Pressure		120 p.s.i. (8.3 bar)
Maximum Material Inlet Pressure		10 p.s.i. (0.69 bar)
Maximum Outlet Pressure		120 p.s.i. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . .		90 g.p.m. (340.7 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . . .		0.64 gal. (2.42 lit.)
Maximum Particle Size		1/4” dia. (6.4 mm)

Maximum Temperature Limits (diaphragm / ball / seat material)

E.P.R. / EPDM	-60_to 280_ F (-51_to 138_ C)
HytrelR	-20_to 150_ F (-29_to 66_ C)
Polypropylene	35_ to 175_ F (2_ to 79_ C)
SantopreneR	-40_to 225_ F (-40_to 107_ C)
PTFE	40_ to 225_ F (4_ to 107_ C)
VitonR	-40_to 350_ F (-40_to 177_ C)
Dimensional Data	. . . . . see page 8

Noise Level @ 70 p.s.i., 60 c.p.m. . . . 77.7 db(A)*

Tested with 93139 muffler assembly installed.

The pump sound pressure levels published here have been updated to an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four mi- crophone locations.

NOTICE: All possible options are shown in the chart. However, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 495-0276 FAX(800) 892-6276 © 2010 CCN 15242621

AD40A-XXX-XXX

1-1/2’’ DIAPHRAGM PUMP

MODEL DESCRIPTION CHART

AD40 A - X X X - X X X

CENTER SECTION MATERIAL

A - Aluminum

THREAD

A- 1-1/2” N.P.T.F. - 1

B- Rp 1-1/2 - 11 BS

FLUID CAPS & MANIFOLD MATERIAL

A- Aluminum C - Cast iron

S - Stainless Steel

HARDWARE MATERIAL

P- Carbon Steel S - Stainless Steel

SEAT MATERIAL

F - Aluminum

P - Polypropylene

S - 316 Stainless Steel

BALL MATERIAL

A- Santoprene C - Hytrel

T - PTFE

DIAPHRAGM MATERIAL

A- Santoprene C - Hytrel

T - PTFE

FLUID SECTION SERVICE KIT SELECTION AD40A - XXX - X X X

EXAMPLE: MODEL # AD40A-ASS-SAA	637426 - X X
FLUID SECTION SERVICE KIT # 637426-AA	Ball	Diaphragm

www.ingersollrandproducts.com