Ingersoll-Rand LM2203A-X-C PARTS LIST / LM2203A-XX-C, General Description, Description size

PARTS LIST / LM2203A-XX-C

Item	Description (size)	(Qty)	Part No.
1	Bolt	(4)	94333
2	Upper Cap	(1)	94307
n 3	Track Gasket	(2)	94311
4	Sleeve	(2)	94316
n 5	“O” Ring (1/16” x 11/16” o.d.)	(4)	Y325-15
n 6	“O” Ring (1/8” x 3/4” o.d.)	(4)	Y325-206
7	Spool	(2)	94310
n 8	“U” Cup (1/8” x 3/4” o.d.)	(2)	Y240-7
n 9	“O” Ring (0.106” x 0.587” o.d.)	(2)	15066-PM
10	Muffler Housing	(1)	94443
11	Cylinder	(1)	94249
12	Retaining Ring	(1)	94406
n 13	“U” Cup (3/16” x 2” o.d.)	(2)	Y240-23
14	Piston	(1)	94780
15	Lower Cap	(1)	94308
n 16	“O” Ring (1/8” x 1-3/8” o.d.)	(1)	Y325-216
17	Bushing	(1)	94332
n 18	Packing (1/4” x 1-5/8” o.d.)	(1)	94337
n 19	“O” Ring (3/32” x 1” o.d.)	(1)	Y325-117
20	Piston Rod	(1)	94779
21	Groove Pin (3/16” o.d. x 1-1/8” long)	(1)	94338
22	Spring	(1)	94705
23	Ball (3/4” dia.)	(1)	Y16-224
24	Inner Check	(1)	94279
n 25	“O” Ring (3/16” x 1-7/16” o.d.)	(1)	Y325-319
26	Base - models LM2203A-( )1-C	(1)	96253
	- models LM2203A-( )2-C	(1)	96253-1
27	Nut	(4)	93828
n 28	Copper Gasket	(1)	96031
29	Tube	(1)	94314-1
n 30	“O” Ring (3/32” x 1-9/16” o.d.)	(1)	Y325-126
31	Ball (1” dia.)	(1)	Y16-232

Item	Description (size)			(Qty)	Part No.
32	Ball Stop Pin (0.187” dia. x 1.430” long)			(1)	94339
33	Foot Valve - models LM2203A-( )1-C			(1)	94315
	- models LM2203A-( )2-C			(1)	94315-1
n 34	“O” Ring (1/16” x 7/16” o.d.)			(1)	Y325-11
n 35	“O” Ring (1/16” x 3/4” o.d.)			(1)	Y325-16
36	Adapter - models LM2203A-( )1-C			(1)	94447
	- models LM2203A-( )2-C			(1)	94447-1
37	Foam Liner			(2)	94402
38	Ground Screw (#10 - 32 x 1/4”)			(1)	93005
39	Bung Assembly (includes items 40 and 49)			(1)	67145-3-B
40	Thumb Screw (1/4” - 20 x 1-1/2”)			(1)	Y197-158-C
41	Pipe Extension	- models LM2203A-31-C		(1)	94523-3
	3/4 - 14 N.P.T. x 30-1/8”	- models LM2203A-41-C		(1)	94523-4
	3/4 - 14 N.P.T. x 37-3/4”	- models LM2203A-51-C		(1)	94523-5
	Rc 3/4 (3/4 - 14 BSP taper x 20-3/8”)		- LM2203A-32-C	(1)	94537-3
	Rc 3/4 (3/4 - 14 BSP taper x 30-1/8”)		- LM2203A-42-C	(1)	94537-4
	Rc 3/4 (3/4 - 14 BSP taper x 37-3/4”)		- LM2203A-52-C	(1)	94537-5
42	Valve Housing - models LM2203A-( )1-C			(1)	94535
	- models LM2203A-( )2-C			(1)	94535-1
43	Ball Guide			(1)	77904
44	Ball (1” dia.)			(1)	Y16-232
n 45	“O” Ring (3/32” x 1-7/16” o.d.)			(1)	Y325-124
46	Ball Seat - models LM2203A-( )1-C			(1)	94534
	- models LM2203A-( )2-C			(1)	94534-1
47	Valve Assembly (includes items 42 thru 46)
	models LM2203A-31-C, -41-C, -51-C			(1)	67085
	models LM2203A-32-C, -42-C, -52-C			(1)	67085-1
48	Washer			(1)	94515
49	Nut (1/4” - 20)			(1)	Y12-4-C
n	Gadus S2 U1000 Grease Packet			(1)	94833
n	Parts in Repair Kit				637224

GENERAL DESCRIPTION

Model LM2203A-X-C series two-ball double acting pumps are intended to be used primarily for oil transfer and delivery systems. It is best to use this pump with low -- medium viscosity fluids. It uses carbon steel and other materials which make it compatible with most petroleum based lu- brication products. The two-ball design provides better priming of the lower foot valve. Double acting pumps will deliver material on both the up and down stroke.

NOTE: If this pump was purchased separately (not part of a system), consult your sales representative for compatible dispensing accesso- ries which will best match the application. All accessories must be able to withstand the maximum pressure developed by the pump.

OPERATING AND SAFETY PRECAUTIONS

WARNING READ THE GENERAL INFORMATION MANUAL INCLUDED FOR ADDITIONAL OPERATING AND SAFETY PRE- CAUTIONS AND OTHER IMPORTANT INFORMATION.

WARNING STATIC SPARK. Can cause explosion resulting in severe injury or death. Ground the pump and pumping system. WARNING EXCESSIVE INLET PRESSURE. Can cause ex-

plosion resulting in severe injury or death. Do not exceed maxi- mum operating pressure of 450 p.s.i. (31.0 bar) at 150 p.s.i. (10.3 bar) inlet air pressure. Do not run pump without using a regula- tor to limit air supply pressure to the pump.

PUMP RATIO X	=	MAXIMUM PUMP
INLET PRESSURE TO PUMP MOTOR		FLUID PRESSURE

Pump ratio is an expression of the relationship between the pump motor area and the lower pump end area. EXAMPLE: When 150 p.s.i. (10.3 bar) inlet pressure is supplied to the motor of a 3:1 ratio pump it will develop a maximum of 450 p.s.i. (31.0 bar) fluid pressure (at no flow) -- as the fluid control is opened, the flow rate will increase as the motor cycle rate increases to keep up with the demand.

WARNING EXCESSIVE MATERIAL PRESSURE. Can cause equipment failure resulting in severe injury or property damage. Do not exceed the maximum material pressure of any compo- nent in the system.

NOTICE: Thermal expansion can occur when the fluid in the materi-

al lines is exposed to elevated temperatures. Example: Material lines located in a non-insulated roof area can warm due to sunlight. Install a pressure relief valve in the pumping system.

Replacement warning label (pn 94520) is available upon request.

Page 2 of 4 LM2203A-X-C