2Turn on your other Rocketboost sender device (sold separately) and make sure the audio source connected to that device is active.
3Press the Next Source button on the remote control to select the Rocketboost input source.
•If there are multiple Rocketboost sources, you may need to press the Next Source button on the soundbar to find the source you want to listen to. Each press will cycle through the available Rocketboost sources.
Sending audio from the soundbar to other Rocketboost products
The selected soundbar audio signal, from either the Television or AUX, is automatically sent on the Rocketboost network.
The soundbar sends two separate audio signals on the Rocketboost network:
-One of the audio signals is designed for use with a subwoofer. This signal is low bass frequency content only and this signal's volume level is set to the same volume as the soundbar. That way your soundbar and subwoofer are correctly set to the same volume level and the subwoofer volume level is easily controlled by the soundbar volume control.
-The second audio signal is designed for listening to the soundbar audio in a second room or with headphones that have their own volume control. This signal's volume level is fixed and does not change with the soundbar volume control. For example, you would use this signal if you are listening to the soundbar's audio signal in another room, and that room's amplifier has its own volume control.
Both audio signals are automatically sent on the Rocketboost network. Every Rocketboost receiver can receive both of these signals. Press the Next Source button on your other Rocketboost product until you hear the signal you want (for example the low frequency signal for the subwoofer.)
To connect a subwoofer using Rocketboost:Note
You can wirelessly connect to a Rocketboost enabled subwoofer or to a typical wired subwoofer. The following instructions are for connecting to a typical wired subwoofer. If you are using a Rocketboost enabled subwoofer, refer the to the user guide for that product.
1Set the Subwoofer Mode Switch on the back of the soundbar to the EXTERNAL position.
2Connect a Rocketboost sender/receiver
Note
You will need to use the dual RCA adapter cable supplied with the
3Follow the steps To establish communications with other Rocketboost devices (see above) to connect the
4Turn on your soundbar and subwoofer and play music or a movie that you can easily hear the bass sound on.
5Press the Next Source button on the
6The soundbar sends both a subwoofer signal (volume controlled by the soundbar) and a second room audio signal (not volume controlled by the soundbar). To confirm you are connected to the subwoofer signal, use the soundbar remote control to turn the volume up and down, and listen to make sure that the subwoofer volume level changes. If it does not, press Next Source on the
Listening to the soundbar audio in another room or through Rocketboost enabled headphones
To listen to the soundbar audio in another room or through Rocketboost enabled headphones:
1Connect and setup your other Rocketboost product (see user guide for that product for more details).
2Turn on your soundbar and play any audio.
3Press the Next Source button on your other Rocketboost device until you hear the soundbar's audio signal. You may have to press Next Source multiple times until you hear the soundbar's audio. Also, when the
Additional Rocketboost setup information
The soundbar is pre configured with both the subwoofer and second room Rocketboost audio signals turned on. For users that don't need these signals sent on the Rocketboost network (for example if you are not using the second room audio signal from the soundbar) you can turn off either of these signals.
To turn off the subwoofer signal:1On the soundbar, press both the Wireless Next Source button and the Volume Up button for five or more seconds.
2The Audyssey Dynamic Volume Green indicator LED will briefly flash on/off twice, to show that the subwoofer signal is now off.
To turn on the subwoofer signal:1On the soundbar, press both the Wireless Next Source button and the Volume Up button for five or more seconds.
2The Audyssey Dynamic Volume Green indicator LED will briefly turn on to show that the subwoofer signal is now on.
8 | www.insigniaproducts.com |