Intermec PX4I Printhead Replacement, cont.

PEFS19J

EasyCoder PX4i User’s Guide (IPL version) 87

Chapter 10 — Maintenance

Connect the two cables to the replace-

ment printhead.

Fit the hooks of the printhead bracket

ﬁ ngers onto the headlift shaft. Make

sure that the cables do not prevent the

bracket ﬁ ngers from being properly

seated on the headlift shaft.

Load a new supply of media and ribbon,

as described earlier in this manual.

Close the printhead so the magnet

engages the printhead bracket.

Printhead Replacement, cont.

Contents

Main Page Page Page Page Page Contents 1 2 3 4 5 6 7 8 9 10 11 Page Before You Begin Safety Summary Do not repair or adjust alone First aid Resuscitation Safety Icons Global Services and Support Page Page Description of EasyCoder PX4i Printer Safety Summary Product Identi cation Page 2 Unpacking the Printer Front View Rear View Media Compartment Print Mechanism Connections Power Computer RS-232 Serial Interface USB Interface Controls and Indicators Indicator Lamps Display Keyboard Page Page Switching On the Printer 4 Tear-O (Straight-through) Tear-O , cont. Tear-O , cont. 10 11 Tear-O , cont. Cut-O Page Cut-O , cont. Cut-O , cont. Page Peel-O (Self-strip) Page 76 5a 5b CMIN Page Internal Batch Takeup (Roll-to-roll) Page Internal Batch Takeup, cont. 6b 7 5 6a Internal Batch Takeup, cont. CMIN 10 11 Page Page External Supply (Fan-fold) 3 4 External Supply (Fan-fold), cont. 5 6 Page Ribbon Load Ribbon Load, cont. 5c 5a 6 5b Ribbon Load, cont. Page 6 Description Default Setup The printers default setup is listed below (no options included): Setup Parameters Serial Communication Baud Rate Data Bits Parity Stop Bits Protocol XON/XOFF (default) Intermec Standard Protocol Test/Service Testprint Con guration Page Media Media Type Paper Type Label Length Dots Sensitivity (Media Sensitivity Number) Darkness Label Rest Point Form Adj Dots X Form Adj Dots Y Ribbon Low Con guration Power Up Emulation Print Speed Cutter (option) Label Taken Sensor (option) Returning to Factory Default Setup Factory Default? Enter=Yes ESC=No Page Navigating in Setup Mode Page 62 EasyCoder PX4i Users Guide (IPL version) Setup Mode; Serial Communication Read-only Read-only Read-only Read-only Read-only These menus will only be displayed when an optional EasyLAN interface board is installed. EasyCoder PX4i Users Guide (IPL version) 63 Setup Mode; Network (option) 64 EasyCoder PX4i Users Guide (IPL version) Setup Mode; Test/Service EasyCoder PX4i Users Guide (IPL version) 65 Setup Mode; Media 66 EasyCoder PX4i Users Guide (IPL version) Setup Mode; Con guration Page Introduction Liner/Batch Takeup Kit Paper Cutter Fan-Fold Guides Media Roll Retainer 3-inch Adapter Label Taken Sensor Interface Boards Page Page Intermec Readiness Indicator Display Messages and LED Indications Page Page Page 10 Printhead Cleaning Printhead Cleaning, cont. Page External Cleaning Cleaning the Label Stop Sensor Printhead Replacement Page Printhead Replacement, cont. Media Jams Page Narrow Media Printhead Pressure Label Stop Sensor Page Page Page Page Page Page Page Media Roll Size Core Roll Page Self-Adhesive Strip Self-Adhesive Labels Page Tickets with Gaps Page Tickets with Black Mark Page Page RS-232 Interface Protocol Interface Cable USB Interface EasyLAN Ethernet Interface Optional Interfaces IEEE 1284 Parallel Interface Board EasyLAN Wireless Interface Page Page Setting the Media Sensitivity Number Page Direct Thermal Media Sensitivity Settings Thermal Transfer Media and Ribbon Sensitivity Settings Page Page *1-960625-01*