Invacare 9805, 9805P SECTION 4ASSEMBLY

SECTION 4—ASSEMBLY

Portable Patient Lift and Sling 16 Part No 1024492

SECTION 4—ASSEMBLY

Assembly of the Patient Lift

 WARNING

Use only Invacare parts in the assembly of this lift. The base legs, the mast, boom,

pump assembly and the swivel bar are manufactured to specifications that assure

correct alignment of all parts for safe functional operation.

CAUTION

DO NOT run the lift until it is fully assembled.

Follow the assembly instrudctions in the Owner’s Manual for proper assembly of

this lift. Failure to do so could result in damage to the push handle of the lift, render-

ing it inoperative.

NOTE: For this procedure, refer to FIGURE4.1 and FIGURE 4.2.

Base, Mast and Boom Assembly

1. Unpack the components from the

shipping cartons.

2. Remove the locking screw from the

bottom of the base.

NOTE: The bottom of the mast assembly will

have a notch.

3. Match the notch at the bottom of the

mast assembly with the tabs inside the

socket of the base assembly.

4. Insert the mast assembly into the socket

and onto the tabs.

5. Turn the mast assembly to make sure

that the notch is locked on the tabs of

the socket.

NOTE: If the mast does not turn, the mast is

centered and locked in place.

6. Insert the locking screw into the bottom

of the base and securely tighten.

 WARNING

The mast may be removed from the

base for storage or transporting. Each

time the mast is removed and returned

to the socket of the base, the mast

MUST be locked into the socket of the

base assembly. FIGURE 4.1 Assembly of the Patient Lift -

Base, Mast and Boom Assembly

Locking Screw

Bolt and Locknut

Bottom of mast notch

Top Inside of the

Socket of the

Base Assembly

Contents

Main WARNING Page TABLE OF CONTENTS REGISTER YOUR PRODUCT PRODUCT REGISTRATION FORM Page LABEL LOCATION Part No 1024492 7Portable Patient Lift and Sling LABEL LOCATION Models 9805 and 9805P WARNING SPECIAL NOTES NOTICE TYPICAL PRODUCT PARAMETERS TYPICAL PRODUCT PARAMETERS SECTION 1GENERAL GUIDELINES Assembling the Lift Operating the Lift Using the Sling Lifting the Patient Transferring the Patient Performing Maintenance SECTION 2FEATURES Hydraulic Lifts Patient Slings Model Nos. 9042, 9043, 9046 and 9047 Slings SECTION 3HANDLING Shipping and Transportation Instructions Unpacking Inspection Storage SECTION 4ASSEMBLY Assembly of the Patient Lift Base, Mast and Boom Assembly Page Base Shifter Handle Assembly Swivel Bar Attachment with Mounting Bracket SECTION 5ONE-PIECE CONTOUR SLINGS Slings Using Chains, O-rings and D-rings Fabric Body Positioning the Contour Sling Positioning the Patient on the Sling Page SECTION 6ATTACHING SLING HARDWARE Attaching the Sling Hardware Inserting the Four Metal Support Bars into the Sling Attaching the Chains or Adjustable Straps to the Sling Page SECTION 7OPERATION Operating the Patient Lift Opening the Legs of the Adjustable Base Raising/Lowering Model Hydraulic Lifts Page SECTION 8LIFTING THE PATIENT Page Page SECTION 9BATHROOM Transferring Patient for Use of Commode Chair or Standard Commode Transferring to a Commode Chair Transferring to a Standard Commode Bathing SECTION 10TRANSFERRING Transferring to a Wheelchair SECTION 10TRANSFERRING FIGURE 10.1 Transferring to a Wheelchair Transferring to a Car Page Transferring from a Car to a Wheelchair SECTION 10TRANSFERRING FIGURE 10.3 Transferring from a Car to a Wheelchair SECTION 11CARE AND MAINTENANCE Hydraulic Pump Lubrication Wear and Damage Cleaning SECTION 11CARE AND MAINTENANCE Maintenance Safety Inspection Checklist ITEM INITIALLY INSTITU- TIONAL INSPECT/ ADJUST MONTHLY IN-HOME ADJUST EVERY SIX MONTHS IN-HOME LIMITED WARRANTY