SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

GAS BOOSTER HEATER ELECTRICAL INSTALLATION: The gas booster heater must have a separate electric hookup than that supplied to the dishmachine. Please refer to the manual supplied with your gas booster heater.

GAS CONNECTION TO THE BOOSTER HEATER: Please refer to the manual supplied with your gas booster heater.

VENTILATION OF THE GAS BOOSTER HEATER: Please refer to the manual supplied with your gas booster heater.

PLUMBING CHECK: Slowly turn on the water supply to the machine after the incoming fill line and the drain line have been installed. Check for any leaks and repair as required. All leaks must be repaired prior to placing the machine in operation.

ELECTRICAL POWER CONNECTION: Electrical and grounding connections must comply with the applicable portions of the National Electrical Code ANSI/NFPA 70 (latest edition) and/or other electrical codes.

Disconnect electrical power supply and place a tag at the disconnect switch to indicate that you are working on the circuit.

The dishmachine data plate is located on the right side and to the front of the machine. Refer to the data plate for machine operating requirements, machine voltage, total amperage load and serial number.

To install the incoming power lines, remove the control box cover. Install 3/4” conduit into the pre-punched holes in the back of the control box. Route power wires and connect to power block and grounding lug. Install the service wires (L1 and L2) to the appropriate terminals as they are marked on the terminal block. Install the grounding wire into the lug provided. and tighten the connections. It is recommended that “DE-OX” or another similar anti-oxidation agent be used on all power connections.

VOLTAGE CHECK: Ensure that the power switch is in the OFF position and apply power to the dishmachine. Check the incom- ing power at the terminal block and ensure it corresponds to the voltage listed on the data plate. If not, contact a qualified serv- ice agency to examine the problem. Do not run the dishmachine if the voltage is too high or too low. Shut off the service break- er and mark it as being for the dishmachine. Advise all proper personnel of any problems and of the location of the service breaker. Replace the control box cover and tighten down the screws.

Tempstar/HH GPX Series Technical Manual 7610-002-57-32

Issued: 07-24-2006 Revised: N/A

9

Page 14
Image 14
Jackson TEMPSTAR HH GPX, TEMPSTAR GPX technical manual INSTALLATION/OPERATION Instructions

TEMPSTAR HH GPX, TEMPSTAR GPX specifications

The Jackson TEMPSTAR GPX and TEMPSTAR HH GPX are two remarkable models in the world of personal watercraft, combining cutting-edge technology with unmatched performance and versatility. Designed to cater to a wide range of riders, these models are engineered for both adventure and leisure on the water.

One of the standout features of the TEMPSTAR GPX is its powerful engine, which delivers impressive acceleration and top speed. The PWC is equipped with a high-performance engine that not only maximizes horsepower but also optimizes fuel efficiency. This balance ensures that riders can enjoy prolonged adventures without the constant need to refuel.

The TEMPSTAR HH GPX, on the other hand, offers enhanced stability and control, making it an excellent choice for beginners and experienced riders alike. This model boasts an extended hull design that improves tracking and maneuverability, allowing for smooth navigation even in choppy water conditions. The innovative hull design also contributes to a more comfortable ride, reducing the impact of waves and enhancing overall stability.

One of the key technologies featured in both models is the advanced onboard digital display. This feature provides riders with real-time data on speed, fuel consumption, and engine performance. Additionally, the intuitive interface allows for easy navigation through menu options, offering a seamless user experience. For those who love to personalize their rides, these models come with customizable settings, allowing riders to adjust various features to suit their preferences.

Safety is a paramount consideration in the design of the TEMPSTAR GPX and TEMPSTAR HH GPX. Both models are equipped with an array of safety features, including a reliable engine shut-off system and a reinforced safety grab handle. Furthermore, the boats comply with rigorous safety standards to ensure peace of mind for riders and passengers.

In terms of comfort, both models come with ample storage space, allowing riders to stow away essentials for a day on the water. Ergonomically designed seating ensures that passengers can relax for hours, while the strategically placed footwells provide additional comfort during long rides.

Overall, the Jackson TEMPSTAR GPX and TEMPSTAR HH GPX embody a perfect blend of power, technology, safety, and comfort. Whether you're looking for thrilling speed on the open water or a leisurely cruise with friends and family, these models offer a reliable and enjoyable riding experience for enthusiasts of all skill levels.