HEAVY DUTY
MECHANICAL
TIME SWITCH
15306• 24 HOUR TIME SWITCH
SWITCH: | SPST |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CONTACT RATINGS: | 40 AMP |
|
|
| 1000VA | |||||||||||||||||||||
| 40 AMP TUNGSTEN 120VAC |
| ||||||||||||||||||||||||
| 20 AMP INDUCTIVE |
|
|
| 2HP 120VAC; 5HP 240VAC | |||||||||||||||||||||
TIMING MOTOR: | 120VAC 60Hz |
|
|
|
|
|
|
|
|
|
| M |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||||
POWER CONSUMPTION: | 3 WATTS MAX |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For seperate motor terminals, remove |
|
|
|
|
| L |
| 1 |
|
|
| X |
| 2 |
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
bridge from terminals L & 1 | Removable |
| H |
|
|
|
|
|
|
|
|
|
|
|
| LOAD |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
120VAC/60Hz | Bridge | N |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| FOR 120 VAC | ||||||||||||||||||||||
|
|
|
|
| ||||||||||||||||||||||
|
|
|
|
|
|
|
| |||||||||||||||||||
We recommend that installation be made by a licensed electrician. Disconnect power at main panel prior to installing or servicing this time switch or the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG
Replace insulator before turning on electricity to unit.
INSTALLATION AND OPERATING INSTRUCTIONS TO SET ON AND
OFF TIMES: Light trippers turn ON.
Dark trippers turn OFF. Place tripper on |
|
|
|
|
| Dial Calibrations |
|
| ||
|
|
|
|
|
|
|
|
|
| |
dial edge as shown in figure and set |
|
|
|
| Knurled Screw |
|
| |||
point of each tripper to desired oper- | OFF TIME |
|
|
|
|
|
| ON TIME | ||
ating time. Note if selected time is AM | (Dark Tripper) |
|
|
|
|
|
| (Light Tripper) | ||
or PM. Hold tripper against dial edge | MANUAL |
| O |
|
| O |
| MANUAL | ||
OFF |
|
| F |
|
|
| ON | |||
and firmly tighten knurled screw. | LEVER |
| F |
|
| N | LEVER | |||
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |
INSTALLATION AND OPERATING INSTRUCTIONS TO SET DIAL TO TIME:
Turn dial
FOR TEMPORARY MANUAL OVERRIDE:
Press down lever on right of nameplate to turn ON. Press down lever on left of nameplate to turn OFF. CAUTION: Do not rotate dial for manual override.
TO REMOVE MECHANISM FROM CASE:
Press lever near case latch to release mainplate and swing the movement out. To replace, insert mainplate projections in slots opposite latch and swing movement in until it latches.
15306
MANUAL VERSION 1 12/15/09
WWW.JASCOPRODUCTS.COM
469D
