JBL S36II For stereo-only applications, For home theater applications, Attempt to mount these

S P E A K E R P L A C E M E N T

Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimal placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure.

For stereo-only applications:

The Studio Series S36II and S36AWII loudspeakers are video- shielded and can safely be placed near a television.

The S36AWII loudspeakers are weather-resistant and are specifically designed for outdoor use, such as in a patio area. As noted below, we recommend mounting the speakers under an

overhang, such as roof eaves, for added protection. The S36AWII speakers, because they are resistant to moisture, are also appropriate for mounting in a bathroom, although not inside a bathtub or shower stall.

Although these loudspeakers are

Less than 6 – 8 feet

More than 6 – 8 feet

For home theater applications:

0-2 ft.

This placement provides a wide spread in sound, supplemented by the center channel speaker.

W A L L - M O U N T I N G

Do not	attempt to mount these	toward the listener when
speakers	on a ceiling, on the	mounted flush against the wall.
underside	of roof eaves or in a	When mounting the S36AWII
shower	stall.	speakers outdoors, we
The S36	II and S36AWII loud-	recommend that you place them
speakers	may be positioned on	under an overhang, such as roof
the wall	either horizontally or	eaves, for added protection, and
vertically.	The grille logo on each	that you use two of the supplied
speaker may be rotated		special angle-mount screws
depending on how the speaker is		per speaker, which angle the
positioned. Gently pull the logo		speakers downward at a greater-
away from the grille slightly, rotate		than-usual angle, facilitating
it to the desired position, and let		water drainage.
go. The logo will snap back into		NOTE: When using the enclosed
place.		angle-mount screws, always use
When mounted vertically, the		the top two screw locations
tweeter array may be positioned		appropriate for the specific
either up or down, depending on		mounting orientation of your
the height of the placement. If the		S36AWII. Referring to the
speakers will be above ear level,		enclosed installation template,
the tweeter array should be		screw locations (1) and (2) are to
positioned down, preferably no		be used when mounting the
more than two feet above ear		S36AWII horizontally so that
level. If the speakers will be		these locations are on top. To
mounted very low, it may be best		mount the loudspeakers
to position the tweeter array		vertically, use locations (2) and
upward so that it will be no more		(4) or locations (1) and (3),
than two feet below ear level.		depending on the mounting
The S36II and S36AWII		orientation. Do not mount the
enclosures are specially		S36AWII upside down (with
designed to angle the speakers		screw locations (3) and (4) on

designed as a mirrored pair, the decision as to which one is left or right will depend on the amount of space left between them.

A wider stereo image is presented with the tweeter/midrange array outboard, and a tighter image is presented with the array inboard.

		Roof eave
	Supplied Angle-Mount Screw
	(When using angle-mount
	screws, always utilize the
		top two screw holes
		on the S36AWII,
	II	depending on
Wall	S36AW
		mounting orientation.)
		Horizontal mounting:
		Use screwholes (1) and (2).
		Vertical mounting: Use
		screwholes (1) and (3), or (2)
	and (4), whichever are uppermost.
	Supplied Rubber Pad

top) because it won’t be able to lock onto the screw heads. Remember that the JBL logo on the tweeter/mid faceplate can be rotated with choice of speaker position (vertical or horizontal).

At least one screw per speaker should be installed in a wooden wall stud. Select an appropriate wall anchor for the other screw. If the special angle-mount screws are not being used, size 10 screws of at least 1-1/2" in length are recommended. If the screws are used in drywall or other surfaces incapable of holding the screw by itself, selection of proper anchors is essential. The customer is solely responsible for proper selection and installation of screws, anchors and other installation hardware. Further installation details are included on the installation template.