Jenn-Air JGR8895BD dimensions 30 76.2 cm Double Oven Gas Range, Product Model Number, Adequate

30" (76.2 cm) Double Oven Gas Range

PRODUCT MODEL NUMBER

JGR8895BD

PRODUCT DIMENSIONS

Gas supply: This range is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to the range location. A smaller size pipe on longer runs may result in insufficient gas supply. Pipe-joint compounds that resist the action of LP gas must be used. Do not use TEFLON®† tape. With LP gas, piping or tubing size can be 1/2" (1.3 cm) minimum. Usually, LP gas suppliers determine the size and materials used in the system.

If local codes permit, a new CSA design-certified, 4 to 5 ft (122 to 152.4 cm) long, 1/2" (1.3 cm) or 3/4" (1.9 cm) I.D., flexible metal appliance connector may be used for connecting range to the gas supply line.

A 1/2" (1.3 cm) male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance pressure regulator.

The supply line must be equipped with a manual shutoff valve. This valve should be located in the same room but external to the range.

Electrical: The range must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is

A. 35⁷⁄₈" (91.1 cm) cooktop height (minimum) with leveling legs screwed all the way in*

B. Model/serial/rating plates (located behind the control panel)**

C. 46³⁄₄" (118.7 cm) overall height (minimum) with leveling legs screwed all the way in*

D. 28¹⁄₈" (71.3 cm) depth with handle

E. 26⁵⁄₁₆" - 27¼" (66.8 - 69.2 cm)*** F. 29⁷⁄₈" (75.9 cm) width

A

F

B*

C**

D

E***

adequate.

A 120-volt, 60-Hz, AC-only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this range be provided. Do not use an extension cord.

†®TEFLON is a registered trademark of E.I. Du Pont Nemours and Company.

CABINET OPENING DIMENSIONS

*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.

**Model/serial/rating plates may be rotated up from behind the control panel for viewing from the front of the range.

***Excludes handle. Dimension given is from wall to front of oven door and will vary based on electric outlet receptacle installation.

	B	D
	C
A
	E
I	F	H
	G H
		8¼"
		(21.0 cm)
		9¼"
		(23.5 cm)
		3"
	3½"	(7.6 cm)	10"
	(8.9 cm)
			(25.4 cm)
	3"		5"
			(12.7 cm)
	(7.6 cm)
	1"		2¼"**
	(2.5 cm)	1¼"*	(5.7 cm)
		(3.1 cm)	15" (38.1 cm)
		3½"	gas line location
		(8.9 cm)

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

Range may be installed with zero clearance to combustible construction at the rear and on the sides below the cooktop.

NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is protected by not less than 1/4" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.

A. 18" (45.7 cm) upper cabinet to countertop B. 13" (33.0 cm) upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to the top of the cooktop, see NOTE. E. 30" (76.2 cm) min. opening width

F. 3" (7.6 cm) min. clearance from both sides of the range to the side wall or other combustible material.

G. 3" (7.6 cm) distance from wall

H. Cabinet door or hinges should not extend into the cutout.

I. Clearance for gas pressure regulator

*Drill on centerline 1¼" (3.1 cm) from rear wall for gas supply line.

**Gas lines and electrical plugs must be installed within the shaded area to ensure proper alignment of this oven with cabinets.

Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation	Ref. W10162494
Instructions packed with product. Specifications subject to change without notice.	10-16-08