Jenn-Air LSE2704W-C, LSG2704W manual Before YOU Call for SERVICE, Check These Points

nBEFORE YOU CALL FOR SERVICE, CHECK THESE POINTS...

IF YOUR

WASHER:

WON'T

WATER

WON'T

WON'T

SPIN OR

LEAKS

IS

TEME IS

FILL

AGITATE

DRAIN

STOPS

WATER

NOISY

INCORRECT

POSSIBLE

REASON

--

DO THIS

TO CORRECT

Plug cord into electrical outlet. Check fuse or reset

X

X

X

X

circuit

breaker.

Set

selector

to proper

cycle and pull

knob out to on position.

X

X

Turn

both

faucets

on

fully.

Straighten hoses. Eliminate kinked hoses. If there is a

X

X

X

drain

restriction,

call

for service.

X

X

X

X

Close lid and pull knob.

Off-balanced load. Redistribute clothes evenly, close

X

X

lid and

pull knob.

Check

for

leveling.

Be sure water

fill is acceptable for load size.

X

Make

sure hose connections

are

tight

at faucets.

X

Make sure end of drain hose is correctly inserted in

and secured to drain facility.

This may be a pause or soak period. Wait several

X

X

minutes

and it may

start

again.

X

Make

sure

washer

is level

and firm

to

the floor.

Make sure temperature selector is correctly set. Make

X

sure hoses are connected to correct faucets and inlet

connections. Be sure water supply is regulated cor-

rectly-. Flush water line before filling washer.

Suds lock -- caused by too much suds. Rewash with

X

X

out detergent.

Use

correct

amount

of low sudsing

detergent.

Check the water heater. It should be set to deliver a

X

minimum of 120°F hot water at the tap. Also check

water heater capacity and recovery rate.

X

X

X

Hose

filter

screens

plugged.

Disconnect

hoses and

dean

screens.

IF YOUR DRYER:

DOES

DOES

DOESN'T DRY

IS

NOT RUN

NOT HEAT

CLOTHES PROPERLY

NOISY

POSSIBLE

REASON

--

DO THIS TO CORRECT

X

• Opening the door during operation stops the dryer. The start button must

be pushed after closing the door to restart the dryer.

X

X

• Be sure

cord is plugged

into a

live electrical

outlet and

the

connection

is

not loose.

• Check fuse or reset circuit breaken

X

X

X

• Close dryer door, set

for proper

cycle and time, then press

start

button

or

dial.

• Be sure dryer is set for a heat setting and not air-fluff.

X

X

• If you have a gas dryer,

check

to see that the

gas valve

is turned

up.

•Clean lint screen and be sure exhaust duct to outside is not blocked.

•Be sure dryer is not overloaded. One washer load should equal one dryer load.

•For time dry, be sure you have selected the proper time for load. For elec- tronic dry, adjust dryness control to more, normal or less dry setting.

X	•	Exhaust	duct	is too	long,	too small,	or has	more	than	2 bends or is made of
		plastic flexible material. Replace with metal.
	•	Heavy	garments were not sorted from lightweight						garments.
	• Washer spin cycle may not be extractin8 water properl_
X	•	Check	to see	if there	are	any foreign	objects	such	as	coins, buttons, or nails
		which could damage clothes as well as the dryer. Remove promptly.

SPECIAL NOTE ON GAS DRYERS: Fumes from products such as paints, varnishes, waxes, etc., can be pulled into the dryer when operating. A gas-like odor in the load will result until the fumes diminish.

9