Jensen JHD1510 operation manual Installation

JHD1510

INSTALLATION

This unit is designed for installation in vehicle cabs with an existing 1-DIN radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. See the dealer where the radio was purchased for kit availability. Always check the kit application before purchasing to make sure the kit works with your vehicle.

Before You Begin

1.Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

2.Remove Transport Screws

Important Notes

•Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.

•Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

•Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle.

•Install the unit where it does not interfere with driving and cannot injure passengers during a sudden or emergency stop.

•If the installation angle exceeds 30º from horizontal, the unit might not give optimum performance.

•Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or subject to excessive dust, dirt or vibration.

DIN Front Mount

1. Slide the mounting sleeve off of the chas-	Dashboard
sis if it has not already been removed. If it
is locked into position, use the removal	Bend Tabs

problem is corrected. Once proper operation is achieved, turn the accessory switch off and proceed with final mounting of the chassis.

7.Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

8.Attach one end of the

perforated support strap

(supplied) to the screw	Dashboard
stud on the rear of the		Support Strap
chassis using the hex nut
provided. Fasten the	Plain Washer
other end of the	Screw (5 x 25mm)
perforated strap to a
	Rubber Bushing
secure part of the		Screw Stud
dashboard either above	Hex Nut (5mm)
or below the radio using
the screw and plain
washer provided. Bend
the strap, as necessary,
to position it. Some
vehicle installations
provide cavity for rear

support. In these applications, place the rubber bushing over the screw stud and insert the radio.

CAUTION: The perforated rear support strap or rear rubber mounting bushing must be used in the installation of the radio. Installation without either may result in damage to the radio or the mounting surface and void the manufacturer’s warranty.

9.Test radio operation by referring to the operating instructions for the unit.

	keys (supplied) to disengage it. The	182
	removal keys are depicted in “Removing	53
2.	the Unit” on page 3.	Screw Stud
	Check the dashboard opening size by
	sliding the mounting sleeve into it. If the
	opening is not large enough, carefully cut
	or file as necessary until the sleeve easily
	slides into the opening. Do not force the
	sleeve into the opening or cause it to bend
	or bow. Check that there will be sufficient
	space behind the dashboard for the radio chassis.
3.	Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.
	With the sleeve fully inserted into the dashboard opening, bend as many of the tabs
	outward as necessary to firmly secure the sleeve to the dashboard.
4.	Place the radio in front of the dashboard opening so the wiring can be brought through the
	mounting sleeve.
5.	Follow the wiring diagram carefully and make certain all connections are secure and
	insulated with crimp connectors or electrical tape to ensure proper operation.
6.	After completing the wiring connections, turn the unit on to confirm operation (vehicle
	accessory switch must be on). If the unit does not operate, recheck all wiring until the

Removing the Unit

To remove the radio after installation, remove the plastic end caps, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit.

Reconnect Battery

When wiring is complete, reconnect the battery negative terminal.

Sleeve

Removal Key

Removal Key

3