S T E P 4
Place the Stealthbox® into the trunk.
Run speaker wire to the Stealthbox® and wire to the terminal. Double check the woofer for proper operation.
S T E P 5
As in the picture, slide the front of the Stealthbox® into place. Then slide the rear of the Stealthbox® into place.
Make sure that the speaker wire and the factory trunk wir- ing do not get caught up between the Stealthbox® and the body of the vehicle.
I N C L U D E D H A R D W A R E
(1)
(1)
(1)
(1)
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type:
Nominal Impedance: 2 ohms mono
Continuous Power Handling: 500 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
| Preamp Output Section |
| Infrasonic Filter |
| "Q" | Center Freq. | Boost (dB) | Amp LP Filter | Amplifier Input Section | Subwoofer Output | |||||||||||
| Output Mode | Filter Slope |
|
|
|
| 1.6 |
| 45 | +10 |
| Mode / Slope | Input Voltage | Input Sens. | Signal Sensing |
|
|
|
| ||
|
|
|
|
|
|
| 1.1 | 2.7 | 35 | 55 | +4 | +13 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0.7 |
| 25 | 70 |
|
|
|
|
|
|
|
|
|
|
| |
| Full Range / Amp Filter / Out Filter | 12dB / 24dB |
| Off / 30Hz | 0.5 | 4.3 | 20 | 85 | 0 | +15 | Off / 12dB / 24dB | Low / High |
| Off / On |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
+12VDC Ground | Remote | 65 | 85 | Filter Mode | 25 | 30 | Bass EQ |
|
|
|
| 55 | 65 |
|
|
| + | + | _ | _ | |
55 |
| 40 |
|
|
|
| 85 |
|
|
| |||||||||||
45 | 120 |
| 18 | 50 |
|
|
|
| Advanced | 45 | 120 |
|
|
| |||||||
JL AUDIO 500/1 |
|
|
|
|
|
|
|
|
| Bass |
|
|
|
|
|
|
|
|
|
| |
40 | 200 | LP / HP | 15 | 60 | Off / On |
|
| Control | 40 | 200 |
|
|
| MONO OUTPUT ONLY | |||||||
Left Ch. | Right Ch. | Filter Freq. (Hz) | Infrasonic Freq. (Hz) | Remote Bass Port | Filter Freq. (Hz) | Left Ch. | Right Ch. |
THREADED INSERT |
STEALTHBOX WALL |
VEHICLE SHEET METAL |
FENDER WASHER |
SOCKET CUP SET SCREW |
FLAT WASHER |
LOCK WASHER |
HEX BOLT |
S T E P 6
From under the vehicle, place the supplied lock washer, flat washer, flat washer, fender washer onto the supplied hex bolt.
Note: For added protection it is recommended that you apply a bead of silicone between the vehicle and the fender washer. After the bolt assembly is tightly secured, it is also recommended that vehicle under- coating material is applied to the exposed assembly.
Place the bolt assembly through the exposed hole and apply the bolt into the threaded insert of the Stealthbox®.
Secure tightly.
The JL Audio 500/1 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 5x7 /
Fits JL Audio Models:
Rear Speaker Size / Location: 5x7 /
Fits JL Audio Models:
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an amplifier recommendation and basic
(954) | www.jlaudio.com |
|
|
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
Page 3 • JL Audio, Inc 2006
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
