S T E P 4
Note: Before drilling, make sure that you are not going to be drilling into any gas lines, brake lines, transmission lines, electrical wiring, transfer case (4x4 vehicles) or anything else that might cause a reduc- tion in your weekly pay. Always wear eye protection when drilling!
With a drill and a
Remove the wax square.
S T E P 5
Run speaker wire from the amplifier’s location to the Stealthbox® location and check for proper operation of the woofer.
I N C L U D E D H A R D W A R E
(1) | (1) | |
(1) | (1) |
(1)
(1)
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type:
Nominal Impedance: 2 ohms mono
Continuous Power Handling: 600 Watts
P o w e r R e c o m m e n d a t i o n
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2 when being used to power your Stealthbox®.
+12VDC Ground Remote | Preamp Output Section | Infrasonic Filter | “Q” | Center Freq. Boost (dB) Amp LP Filter | Amplifier Input Section | Subwoofer Output |
Output Mode | Filter Slope |
| Mode |
| 1.6 |
| 40 | +10 |
| Mode Slope | Input Voltage | Input Sens. | Signal Sensing | ||
| 1.1 | 2.7 | 30 | 60 | +4 | +13 | |||||||||
|
|
|
|
| 0.7 |
| 25 | 75 |
|
|
|
|
|
|
|
Full Range Amp Filter Out Filter | 12dB 24dB |
| Off On | 0.5 | 4.3 | 20 | 80 | 0 | +15 | Off 12dB 24dB | Low High |
| Off On | ||
|
| 65 | Filter Mode | 30 |
| Bass EQ |
|
|
|
|
| 65 |
|
|
|
| 55 | 80 | 22 | 45 |
|
| Advanced | 55 | 80 |
|
|
| |||
500/1v2 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
45 | 100 |
| 18 | 55 |
|
|
| Bass |
| 45 | 100 |
|
| MONO OUTPUT ONLY | |
Monoblock Subwoofer Amplifier | 40 | 200 | LP HP | 15 | 60 | Off On |
|
| Control |
| 40 | 200 |
|
| |
Left Output Right Output | Filter Freq. (Hz) | Infrasonic Freq. (Hz) | Remote Bass Port | Filter Freq. (Hz) | Left Ch. | Right Ch. |
STEALTHBOX WALL | THREADED INSERT |
| |
| VEHICLE SHEET METAL |
FENDER WASHER | SOCKET CUP SET SCREW |
| |
FENDER WASHER |
|
LOCK WASHER |
|
HEX NUT |
|
S T E P 6
From under the vehicle, place a supplied fender washer, flat washer, lock washer and then hex nut onto the socket cup set screw and secure.
Note: For added protection it is recommended that you apply a bead of silicone between the vehicle and the fender washer. After the bolt assembly is tightly secured, it is also recommended that vehicle under- coating material is applied to the exposed assembly
The JL Audio 500/1v2 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.
M I D / H I G H F r e q u e n c y D r i v e r F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
Fits JL Audio Models:
Rear Speaker Size / Location:
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an amplifier recommendation and basic
Fits JL Audio Models:
(954) | www.jlaudio.com |
|
|
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
Page 3 • JL Audio, Inc 2007
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
