S T E P 4
(A)Posistion the Stealthbox® into place and press firmly down. This is to make an impression onto the wax square. Remove the Stealthbox®.
(B)With a 1/2" drill bit or StepBit/Unibit® and drill. Drill at the impression on the wax square, through the metal floor to the outside.
(C)Remove the wax sqaure.
S T E P 5
(A)Loosen the socket cup set screw to expose
(B)Run speaker wire from the amplifier location to the Stealthbox® and attach to the terminal
Double check the woofer for proper operation.
|
|
| ||
I N C L U D E D H A R D W A R E |
|
|
| |
(1) | (1) | |||
(1) | (1) | |||
(1)
(1)
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type:
Nominal Impedance: 4 ohms mono
Continuous Power Handling: 300 Watts
P O W E R R E C O M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
+12VDC Ground Remote | Preamp Output Section | Bass Control | Amp LP Filter | Amplifier Input Section | |||
| Output Mode | Infrasonic Filter | Mode/Slope | Input Voltage | Input Sens. Signal Sensing | ||
|
| Off/30Hz | Off/12dB/24dB | Low/High | Off/On | ||
|
|
|
| +7 |
|
|
|
|
|
| +3 | +10 |
|
|
|
JL AUDIO 250/1 |
|
| +1 | +13 |
|
|
|
|
|
|
|
|
|
| |
monoblock subwoofer amplifier |
|
|
|
|
|
|
|
| Left Ch. | Right Ch. | LF Boost (dB) | Filter Freq. (Hz) | Left Ch. | Right Ch. | |
THREADED INSERT |
STEALTHBOX WALL |
VEHICLE SHEET METAL |
FENDER WASHER |
SOCKET CUP SET SCREW |
FLAT WASHER |
LOCK WASHER |
HEX NUT |
S T E P 6
From under the vehicle, place the supplied fender washer, flat washer, lock washer and then hex nut onto the protrud- ing socket cup set screw. Secure tightly with a 14mm socket, long extension and rachet.
Note: For added protection it is recommended that you apply a bead of silicone between the vehicle and the fender washer. After the bolt assembly is tightly secured, it is also recommended that vehicle under- coating material is applied to the exposed assembly.
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for even more detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
Fits JL Audio Models:
Rear Speaker Size / Location:
Fits JL Audio Models:
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an amplifier recommendation and basic
(954) | www.jlaudio.com |
|
|
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
Page 2 • JL Audio, Inc 2006
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
